Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Microstrip Impedance Calculator

Microstrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.

5 cited sources34 reference checksRuns in your browser

Inputs

Microstrip cross-section: trace of width W and thickness T on a substrate of height H over a ground planeWHTεr

Use the design (not process) Dk at your frequency from the laminate datasheet.

Copper 58 MS/m (annealed 59.6); gold 41; aluminium 37.7.

RMS profile of the copper. Typical: rolled 0.3–0.5 µm, VLP/HVLP 0.5–2 µm, standard ED 2–5 µm.

Results

Characteristic impedance at f(Z₀(f))
49.367
Effective permittivity at f(εeff(f))
2.8678
Quasi-static impedance(Z₀)
49.267
Quasi-static εeff(εeff)
2.8125
Propagation delay(τ)
143.48
Guided wavelength(λg)
17.703
Conductor loss(αc)
3.1247
Dielectric loss(αd)
5.1109
Total loss(α)
8.2355
Surface-wave (TM₁) onset(f_TM1)
106.21

Formulas

Z0,air(u)=η02πln⁡ ⁣[f(u)u+1+4u2], f(u)=6+(2π−6) e−(30.666/u)0.7528Z_{0,\mathrm{air}}(u) = \frac{\eta_0}{2\pi}\ln\!\left[\frac{f(u)}{u} + \sqrt{1+\frac{4}{u^2}}\right],\ f(u)=6+(2\pi-6)\,e^{-(30.666/u)^{0.7528}}εeff=εr+12+εr−12(1+10u)−a(u) b(εr)\varepsilon_{\mathrm{eff}} = \frac{\varepsilon_r+1}{2} + \frac{\varepsilon_r-1}{2}\left(1+\frac{10}{u}\right)^{-a(u)\,b(\varepsilon_r)}εeff(f)=εr−εr−εeff1+P(f)\varepsilon_{\mathrm{eff}}(f) = \varepsilon_r - \frac{\varepsilon_r-\varepsilon_{\mathrm{eff}}}{1+P(f)}αc=RsZ0W KiKr,αd=πλ0εrεr−1εeff−1εefftan⁡δ\alpha_c = \frac{R_s}{Z_0 W}\,K_i K_r,\quad \alpha_d = \frac{\pi}{\lambda_0}\frac{\varepsilon_r}{\varepsilon_r-1}\frac{\varepsilon_{\mathrm{eff}}-1}{\sqrt{\varepsilon_{\mathrm{eff}}}}\tan\delta

What this calculator does

A microstrip is a signal trace on the outer layer of a PCB, separated from a ground plane by a dielectric of height HH. Part of its field is in the dielectric and part is in the air above, so the wave travels with an effective permittivity εeff\varepsilon_\text{eff} between 1 and εr\varepsilon_r. That number sets both the characteristic impedance and the propagation delay.

This calculator gives you:

  • the quasi-static impedance Z0Z_0 and εeff\varepsilon_\text{eff} (Hammerstad–Jensen), which is what most fabricators' impedance tables quote;
  • the frequency-dependent Z0(f)Z_0(f) and εeff(f)\varepsilon_\text{eff}(f) (Kirschning–Jansen), which matter above a few GHz, where more of the field moves into the substrate;
  • conductor and dielectric loss per unit length, including copper roughness;
  • the surface-wave onset frequency, above which a quasi-TEM model no longer applies.

Designing a 50 Ω trace

Click ⇄ Solve next to Trace width, choose Characteristic impedance at f as the target, and enter 50. The calculator inverts the model numerically and shows the width that gives exactly 50 Ω. You can solve for the substrate height or dielectric constant the same way, for example to back-calculate the effective εr\varepsilon_r from a measured impedance.

Worked example

Rogers RO4350B, H=0.508H = 0.508 mm (20 mil), εr=3.66\varepsilon_r = 3.66, 1 oz copper (T=35 μT = 35\,\mum), at 10 GHz. A 1.1 mm trace gives Z0(f)≈49.4Z_0(f) \approx 49.4 Ω with εeff(f)≈2.87\varepsilon_\text{eff}(f) \approx 2.87. That is a delay of about 143.5 ps/in, and the guided wavelength is about 17.7 mm. To hit exactly 50 Ω, use ⇄ Solve on the trace width: the answer is slightly narrower than 1.1 mm.

Accuracy and validity

ModelQuantityStated accuracyRange
Hammerstad–JensenZ0Z_0, εeff\varepsilon_\text{eff} (static)better than 0.2 % (vs. the original paper's reference)0.01≤W/H≤1000.01 \le W/H \le 100, εr≤128\varepsilon_r \le 128
Kirschning–Jansenεeff(f)\varepsilon_\text{eff}(f)about 0.6 %0.1≤W/H≤1000.1 \le W/H \le 100, 1≤εr≤201 \le \varepsilon_r \le 20, H/λ0≤0.13H/\lambda_0 \le 0.13
Jansen–KirschningZ0(f)Z_0(f)about 2.5 %same as above

The calculator warns when your inputs fall outside these ranges. Real boards add effects that no closed-form model includes: solder mask (it lowers Z0Z_0 by roughly 1–3 Ω), trapezoidal etching, glass-weave variation, and εr\varepsilon_r that changes with frequency. For production stackups, confirm against your fabricator's field-solver result.

Loss

Conductor loss uses the surface resistance Rs=πfμ0/σR_s = \sqrt{\pi f \mu_0/\sigma} with a current-distribution factor KiK_i and the Hammerstad roughness factor Kr=1+2πarctan⁡ ⁣[1.4 (Δ/δ)2]K_r = 1 + \tfrac{2}{\pi}\arctan\!\left[1.4\,(\Delta/\delta)^2\right], where Δ\Delta is the RMS surface roughness and δ\delta the skin depth. This roughness model saturates at 2×. For very rough foils at mm-wave frequencies, the Huray model (coming to this site) is more accurate.

References

  1. E. Hammerstad and Ø. Jensen, “Accurate Models for Microstrip Computer-Aided Design,” IEEE MTT-S Int. Microwave Symp. Digest, 1980, pp. 407–409.
  2. M. Kirschning and R. H. Jansen, “Accurate Model for Effective Dielectric Constant of Microstrip with Validity up to Millimetre-Wave Frequencies,” Electronics Letters, vol. 18, no. 6, pp. 272–273, 1982.
  3. R. H. Jansen and M. Kirschning, “Arguments and an Accurate Model for the Power-Current Formulation of Microstrip Characteristic Impedance,” AEÜ, vol. 37, pp. 108–112, 1983.
  4. E. Hammerstad and F. Bekkadal, Microstrip Handbook, ELAB Report STF44 A74169, University of Trondheim, 1975 (roughness factor).
  5. I. Bahl and P. Bhartia, Microwave Solid State Circuit Design, 2nd ed., Wiley, 2003 (surface-wave onset).

This calculator's results are checked against 34 independent reference values in automated tests on every change. How we check accuracy.