Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

VSWR to Return Loss Calculator (Γ, Mismatch Loss)

Convert between VSWR, return loss, reflection coefficient |Γ|, mismatch loss and transmitted power. Solve from any of them.

1 cited source7 reference checksRuns in your browser

Inputs

Use “Solve for” to enter return loss, |Γ| or mismatch loss instead.

Results

Reflection coefficient |Γ|(|Γ|)
0.2
Return loss(RL)
13.979dB
Mismatch loss(ML)
0.17729dB
Reflected power
4%
Transmitted power
96%

Formulas

∣Γ∣=VSWR−1VSWR+1|\Gamma| = \frac{\mathrm{VSWR}-1}{\mathrm{VSWR}+1}RL=−20log⁡10∣Γ∣  dB\mathrm{RL} = -20\log_{10}|\Gamma|\ \ \mathrm{dB}ML=−10log⁡10(1−∣Γ∣2)  dB\mathrm{ML} = -10\log_{10}\left(1-|\Gamma|^2\right)\ \ \mathrm{dB}

Four ways to describe one mismatch

When a load impedance ZLZ_L differs from the line impedance Z0Z_0, part of the incident wave reflects. The reflection coefficient Γ=(ZL−Z0)/(ZL+Z0)\Gamma = (Z_L - Z_0)/(Z_L + Z_0) is the ratio of reflected to incident voltage. VSWR, return loss and mismatch loss are all functions of ∣Γ∣|\Gamma|:

  • VSWR is the ratio of maximum to minimum voltage along the line (1:1 is a perfect match).
  • Return loss is how far below the incident power the reflected power is, in dB. Larger is better.
  • Mismatch loss is the drop in power delivered to the load caused by the reflection.

To start from return loss or ∣Γ∣|\Gamma| instead of VSWR, click ⇄ Solve next to VSWR and pick the quantity you know.

Quick reference

VSWR|Γ|Return lossMismatch lossPower reflected
1.100.04826.4 dB0.010 dB0.2 %
1.220.10020.0 dB0.044 dB1.0 %
1.500.20014.0 dB0.177 dB4.0 %
1.920.31610.0 dB0.458 dB10 %
2.000.3339.5 dB0.512 dB11.1 %
3.000.5006.0 dB1.249 dB25 %

Sign convention

Return loss is a positive number of dB (RL = 14 dB). S11S_{11} is the same quantity with a negative sign (S11S_{11} = −14 dB). Both describe the same match.

References

  1. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, §2.3.

This calculator's results are checked against 7 independent reference values in automated tests on every change. How we check accuracy.