Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Coplanar Waveguide (CPW / GCPW) Calculator

Coplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.

6 cited sources40 reference checksRuns in your browser

Inputs

Grounded coplanar waveguide cross-section: centre conductor W with gaps S to coplanar grounds on a substrate of height hWSShtεr

Results

Characteristic impedance at f(Z₀(f))
48.628
Effective permittivity at f(εeff(f))
2.4648
Propagation delay(τ)
133.02
Total loss(α)
7.5375
Quasi-static impedance(Z₀)
48.771
Quasi-static εeff(εeff)
2.4503
Conductor loss(αc)
3.214
Dielectric loss(αd)
4.3235
Guided wavelength(λg)
19.095
Substrate TE₀ surface-wave cutoff(f_TE)
90.46
  • W + 2S > 2h: the backside ground dominates and the line behaves largely like a microstrip; keep coplanar grounds wide and via-stitched.
  • The model assumes infinitely wide coplanar grounds tied to the backside. Finite grounds without via fences support parasitic parallel-plate and patch modes.
  • The dispersion fit (Frankel et al.) was derived for CPW without a backside; for GCPW treat εeff(f) as an estimate.

Formulas

k1=WW+2S,k2=sinh⁡(πW/4h)sinh⁡(π(W+2S)/4h),k3=tanh⁡(πW/4h)tanh⁡(π(W+2S)/4h)k_1 = \frac{W}{W+2S},\quad k_2 = \frac{\sinh(\pi W/4h)}{\sinh(\pi(W+2S)/4h)},\quad k_3 = \frac{\tanh(\pi W/4h)}{\tanh(\pi(W+2S)/4h)}CPW:  εeff=1+εr−12K(k2)K(k1′)K(k2′)K(k1),Z0=η04εeffK(k1′)K(k1)\text{CPW: }\ \varepsilon_\mathrm{eff} = 1+\frac{\varepsilon_r-1}{2}\frac{K(k_2)K(k_1')}{K(k_2')K(k_1)},\qquad Z_0 = \frac{\eta_0}{4\sqrt{\varepsilon_\mathrm{eff}}}\frac{K(k_1')}{K(k_1)}GCPW:  εeff=1+εr K(k3)K(k1′)K(k3′)K(k1)1+K(k3)K(k1′)K(k3′)K(k1),Z0=η02εeff 1K(k1)K(k1′)+K(k3)K(k3′)\text{GCPW: }\ \varepsilon_\mathrm{eff} = \frac{1+\varepsilon_r\,\frac{K(k_3)K(k_1')}{K(k_3')K(k_1)}}{1+\frac{K(k_3)K(k_1')}{K(k_3')K(k_1)}},\qquad Z_0 = \frac{\eta_0}{2\sqrt{\varepsilon_\mathrm{eff}}}\,\frac{1}{\frac{K(k_1)}{K(k_1')}+\frac{K(k_3)}{K(k_3')}}Δ=1.25tπ[1+ln⁡4πWt],ke=k1+(1−k12)Δ2S,εefft=εeff−0.7(εeff−1)t/SK(k1)/K(k1′)+0.7t/S\Delta = \frac{1.25t}{\pi}\left[1+\ln\frac{4\pi W}{t}\right],\quad k_e = k_1+(1-k_1^2)\frac{\Delta}{2S},\quad \varepsilon_\mathrm{eff}^t = \varepsilon_\mathrm{eff}-\frac{0.7(\varepsilon_\mathrm{eff}-1)t/S}{K(k_1)/K(k_1')+0.7t/S}εeff(f)=εeff+εr−εeff1+G (f/fTE)−1.8,fTE=c4hεr−1\sqrt{\varepsilon_\mathrm{eff}(f)} = \sqrt{\varepsilon_\mathrm{eff}}+\frac{\sqrt{\varepsilon_r}-\sqrt{\varepsilon_\mathrm{eff}}}{1+G\,(f/f_{TE})^{-1.8}},\quad f_{TE} = \frac{c}{4h\sqrt{\varepsilon_r-1}}αc=Rsεeff4η0K(k1)K(k1′)(1−k12)[π+ln⁡(na)a+π+ln⁡(nb)b], n=8π(1−k1)t(1+k1), a=W2, b=a+S\alpha_c = \frac{R_s\sqrt{\varepsilon_\mathrm{eff}}}{4\eta_0 K(k_1)K(k_1')(1-k_1^2)}\left[\frac{\pi+\ln(n a)}{a}+\frac{\pi+\ln(n b)}{b}\right],\ n=\frac{8\pi(1-k_1)}{t(1+k_1)},\ a=\tfrac W2,\ b=a+S

What this calculator does

A coplanar waveguide (CPW) puts the signal conductor and its ground on the same layer. A centre strip of width WW is separated from two wide coplanar grounds by gaps of width SS, on a substrate of height hh. Adding a metal plane under the substrate gives grounded CPW (GCPW, also called conductor-backed CPW). GCPW is the usual choice on RF PCBs, because the backside plane provides mechanical support, heat sinking and a DC ground, and the coplanar grounds are stitched to it with vias.

The impedance is set mainly by the ratio W/(W+2S)W/(W+2S), so a 50 Ω CPW can be made almost any width. That is why CPW is popular for probe pads, connector launches and mm-wave circuits. The calculator gives Z0Z_0 and εeff\varepsilon_\text{eff} both quasi-statically and at your frequency, the delay, and conductor and dielectric loss.

The models

All quasi-static results come from conformal mapping (Ghione & Naldi; Simons, ch. 2). With k1=W/(W+2S)k_1 = W/(W+2S):

  • CPW on a substrate of finite height (air below). The substrate's share of the field is set by k2=sinh⁡(πW/4h)/sinh⁡(π(W+2S)/4h)k_2 = \sinh(\pi W/4h)/\sinh(\pi(W+2S)/4h):

    εeff=1+εr−12 K(k2)/K(k2′)K(k1)/K(k1′),Z0=η04εeff K(k1′)K(k1).\varepsilon_\text{eff} = 1 + \frac{\varepsilon_r-1}{2}\,\frac{K(k_2)/K(k_2')}{K(k_1)/K(k_1')},\qquad Z_0 = \frac{\eta_0}{4\sqrt{\varepsilon_\text{eff}}}\,\frac{K(k_1')}{K(k_1)}.
  • Grounded CPW. The backside plane adds a parallel microstrip-like capacitance with k3=tanh⁡(πW/4h)/tanh⁡(π(W+2S)/4h)k_3 = \tanh(\pi W/4h)/\tanh(\pi(W+2S)/4h):

    Z0=η02εeff 1K(k1)/K(k1′)+K(k3)/K(k3′).Z_0 = \frac{\eta_0}{2\sqrt{\varepsilon_\text{eff}}}\,\frac{1}{K(k_1)/K(k_1') + K(k_3)/K(k_3')}.

Metal thickness widens the strip by Δ=1.25tπ[1+ln⁡(4πW/t)]\Delta = \frac{1.25t}{\pi}\left[1+\ln(4\pi W/t)\right], narrows the gap, and pulls some field into the air between the conductor sidewalls (Gupta et al., eqs. 7.98–7.100).

Dispersion follows the Frankel et al. fit, in which εeff(f)\varepsilon_\text{eff}(f) rises toward εr\varepsilon_r as ff approaches the substrate's TE₀ surface-wave cutoff fTE=c/(4hεr−1)f_{TE} = c/(4h\sqrt{\varepsilon_r-1}). The impedance scales as Z0(f)=Z0εeff/εeff(f)Z_0(f) = Z_0\sqrt{\varepsilon_\text{eff}/\varepsilon_\text{eff}(f)}.

Losses. Conductor loss uses Ghione's closed form, derived from the incremental-inductance rule, which captures the current crowding at the gap edges. Dielectric loss uses the filling-factor formula shared with microstrip.

How to use solve-for

Click ⇄ Solve next to Gap to coplanar ground (or Centre conductor width) and enter a target impedance. A common workflow is to fix WW to match a connector pin or probe pitch, then solve for SS. You can also solve for the substrate height or back out εr\varepsilon_r from a measured impedance.

Worked example

GCPW on 0.508 mm (20 mil) RO4350B-type laminate, with εr=3.66\varepsilon_r = 3.66, tan⁡δ=0.0037\tan\delta = 0.0037, W=0.9W = 0.9 mm, S=0.25S = 0.25 mm and 1 oz copper (t=35 μt = 35\,\mum), at 10 GHz (the defaults):

  • Quasi-static: Z0=48.771Z_0 = 48.771 Ω and εeff=2.4503\varepsilon_\text{eff} = 2.4503.
  • At 10 GHz: Z0(f)=48.628Z_0(f) = 48.628 Ω, εeff(f)=2.4648\varepsilon_\text{eff}(f) = 2.4648, delay 133.02 ps/in, λg=19.095\lambda_g = 19.095 mm.
  • Losses: conductor 0.08164 dB/in and dielectric 0.1098 dB/in, so 0.1915 dB/in in total.
  • The substrate TE₀ cutoff is 90.46 GHz.

To reach exactly 50 Ω at 10 GHz, solve for the gap: S=0.2933S = 0.2933 mm. Without the backside metal (CPW option), the same geometry gives Z0(f)=63.083Z_0(f) = 63.083 Ω. Here W+2S>2hW + 2S > 2h, so the backside plane dominates the capacitance, and the calculator notes that the line behaves largely like a microstrip.

Accuracy and validity

QuantitySourceAccuracy
Z0Z_0, εeff\varepsilon_\text{eff} (t=0t = 0)Conformal mappingExact for infinitely wide grounds (CPW on a half-space, εeff=(εr+1)/2\varepsilon_\text{eff} = (\varepsilon_r+1)/2); within ≈ 1 % for finite hh in practical ranges
Thickness correctionGupta et al.First-order. Good while t≪St \ll S; the calculator warns when t>0.2St > 0.2S
εeff(f)\varepsilon_\text{eff}(f)Frankel et al. fitDerived for CPW without a backside; an estimate for GCPW
αc\alpha_cGhione, incremental inductanceNeeds t>3δt > 3\delta; ignores roughness and backside current
αd\alpha_dFilling-factor formulaExact to the extent εeff\varepsilon_\text{eff} is

All results were cross-checked against scikit-rf's CPW media, which implements the same papers independently (Qucs heritage). Z0Z_0 and εeff\varepsilon_\text{eff} agree to better than 10−410^{-4}, both with and without the metal backside. While checking, we found that scikit-rf 2.2.0 passes the elliptic modulus where SciPy expects the parameter m=k2m = k^2 in its CPW conductor-loss formula. That makes its αc\alpha_c about 20 % low. After that factor is corrected, the conductor and dielectric losses agree to better than 0.5 %.

Practical notes

  • Grounds must be grounds. The formulas assume the coplanar grounds are wide (at least 2(W+2S)2(W+2S) to 3(W+2S)3(W+2S) each) and, for GCPW, tied to the backside with a via fence along both edges at a pitch well below λg/10\lambda_g/10. Without vias, the two coplanar grounds can be driven against each other (the slotline mode), and the GCPW structure can resonate as a patch antenna.
  • GCPW versus microstrip. When hh is small compared with W+2SW+2S, most of the field goes to the backside plane, and the coplanar grounds only trim the impedance. That is fine, and it is the typical PCB situation. For a "true" coplanar line, make h>W+2Sh > W + 2S.
  • Solder mask and plating sit right in the gap, where the field is strongest. They change Z0Z_0 more than they would on a microstrip. Expect a few ohms lower with solder mask in the gaps.
  • Etching. Narrow gaps are hard to hold. For a 0.3 mm centre strip on 20 mil GCPW, a 25 µm change in SS around 0.15 mm moves Z0Z_0 by 3–4 Ω, so check your fabricator's minimum gap and tolerance before you commit to a geometry.
  • Above the surface-wave cutoff the line leaks power into the substrate. Keep the operating frequency well below fTEf_{TE}, which falls quickly with thicker or higher-εr\varepsilon_r substrates.

References

  1. G. Ghione and C. Naldi, “Analytical Formulas for Coplanar Lines in Hybrid and Monolithic MICs,” Electronics Letters, vol. 20, no. 4, pp. 179–181, Feb. 1984.
  2. G. Ghione and C. Naldi, “Parameters of Coplanar Waveguides with Lower Ground Plane,” Electronics Letters, vol. 19, no. 18, pp. 734–735, Sept. 1983.
  3. R. N. Simons, Coplanar Waveguide Circuits, Components, and Systems, Wiley-IEEE Press, 2001, ch. 2.
  4. K. C. Gupta, R. Garg, I. Bahl and P. Bhartia, Microstrip Lines and Slotlines, 2nd ed., Artech House, 1996, eqs. 7.98–7.100 (thickness).
  5. M. Y. Frankel, S. Gupta, J. A. Valdmanis and G. A. Mourou, “Terahertz Attenuation and Dispersion Characteristics of Coplanar Transmission Lines,” IEEE Trans. Microwave Theory Tech., vol. 39, no. 6, pp. 910–916, June 1991.
  6. G. Ghione, “A CAD-Oriented Analytical Model for the Losses of General Asymmetric Coplanar Lines in Hybrid and Monolithic MICs,” IEEE Trans. Microwave Theory Tech., vol. 41, no. 9, pp. 1499–1510, Sept. 1993.

This calculator's results are checked against 40 independent reference values in automated tests on every change. How we check accuracy.