Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Stripline Impedance Calculator

Symmetric and offset stripline Z0, delay, conductor and dielectric loss, and TE-mode cutoff. Exact Cohn solution plus Wheeler thickness. Solve for W, b or εr.

5 cited sources16 reference checksRuns in your browser

Inputs

Centred stripline cross-section: strip of width W and thickness t between ground planes spaced b apartWbtεr

Distance between the two ground planes (total dielectric thickness, including the strip).

Stripline is a homogeneous TEM line: use the Dk of the material that fills the whole cavity (core and prepreg together).

Copper 58 MS/m. Surface roughness is not included.

Results

Characteristic impedance(Z₀)
48.503
Propagation delay(τ)
162.09
Total loss(α)
14.57
Higher-order (TE) mode cutoff(f_c,TE)
121.91
Conductor loss(αc)
8.127
Dielectric loss(αd)
6.443
Capacitance per length(C′)
131.57
Inductance per length(L′)
309.52
Guided wavelength(λg)
15.67

Formulas

Z0∣t=0=η04εr K(k)K(k′),k=sech⁡πW2b, k′=tanh⁡πW2bZ_0\big|_{t=0} = \frac{\eta_0}{4\sqrt{\varepsilon_r}}\,\frac{K(k)}{K(k')},\quad k=\operatorname{sech}\frac{\pi W}{2b},\ k'=\tanh\frac{\pi W}{2b}ZW(t)=η04πεrln⁡ ⁣{1+4πb−tW′[8πb−tW′+(8πb−tW′)2+6.27]},Z0(t)=Z0∣t=0 ZW(t)ZW(0)Z_W(t) = \frac{\eta_0}{4\pi\sqrt{\varepsilon_r}}\ln\!\left\{1+\frac{4}{\pi}\frac{b-t}{W'}\left[\frac{8}{\pi}\frac{b-t}{W'}+\sqrt{\left(\frac{8}{\pi}\frac{b-t}{W'}\right)^2+6.27}\right]\right\},\quad Z_0(t) = Z_0\big|_{t=0}\,\frac{Z_W(t)}{Z_W(0)}ΔWb−t=xπ(1−x){1−12ln⁡ ⁣[(x2−x)2+(0.0796 xW/b+1.1x)m]}, x=tb, m=21+23x1−x\frac{\Delta W}{b-t} = \frac{x}{\pi(1-x)}\left\{1-\tfrac12\ln\!\left[\left(\frac{x}{2-x}\right)^2+\left(\frac{0.0796\,x}{W/b+1.1x}\right)^m\right]\right\},\ x=\frac{t}{b},\ m=\frac{2}{1+\frac23\frac{x}{1-x}}Z0,offset=2 Z0(2h1+t) Z0(2h2+t)Z0(2h1+t)+Z0(2h2+t)Z_{0,\text{offset}} = \frac{2\,Z_0(2h_1+t)\,Z_0(2h_2+t)}{Z_0(2h_1+t)+Z_0(2h_2+t)}αc=Rs2ηZ0 ∂Z0∂n,αd=πfεrtan⁡δc,fc,TE=c2εr (W+πb/4)\alpha_c = \frac{R_s}{2\eta Z_0}\,\frac{\partial Z_0}{\partial n},\qquad \alpha_d = \frac{\pi f\sqrt{\varepsilon_r}\tan\delta}{c},\qquad f_{c,\mathrm{TE}} = \frac{c}{2\sqrt{\varepsilon_r}\,(W+\pi b/4)}

What this calculator does

A stripline is a flat conductor of width WW and thickness tt buried in a dielectric between two ground planes spaced bb apart. It is the standard inner-layer trace of a multilayer PCB. Because the dielectric surrounds the strip completely, the line carries a pure TEM wave. Its effective permittivity is simply εr\varepsilon_r, the delay is εr/c\sqrt{\varepsilon_r}/c for any width, and the impedance depends only on the cross-section.

The calculator handles two geometries:

  • Centred (symmetric) stripline, with the strip midway between the planes.
  • Offset (asymmetric) stripline, with the strip at height h1h_1 above the lower plane and b−t−h1b - t - h_1 below the upper one. This is the usual case in real stack-ups, where the core and the prepreg have different thicknesses.

The outputs are Z0Z_0, delay, capacitance and inductance per length, conductor and dielectric loss, and the cutoff of the first higher-order mode.

The models

Zero thickness, centred. Cohn's conformal mapping gives the exact result

Z0=η04εr K(k)K(k′),k=sech⁡πW2b, k′=tanh⁡πW2b,Z_0 = \frac{\eta_0}{4\sqrt{\varepsilon_r}}\,\frac{K(k)}{K(k')},\qquad k = \operatorname{sech}\frac{\pi W}{2b},\ k'=\tanh\frac{\pi W}{2b},

where KK is the complete elliptic integral of the first kind.

Finite thickness. Wheeler's 1978 formula models a thick strip as a zero-thickness strip of increased width W′=W+ΔWW' = W + \Delta W. Wheeler quotes 0.5 % accuracy for W′/(b−t)<10W'/(b-t) < 10. On its own, Wheeler's formula at t=0t = 0 differs from Cohn's exact value by up to 0.5 %. To keep the result exact at t=0t = 0 and continuous as tt grows, the calculator applies Wheeler's thickness effect as a ratio: Z0(t)=Z0Cohn⋅ZW(t)/ZW(0)Z_0(t) = Z_0^\text{Cohn}\cdot Z_W(t)/Z_W(0). Against a 2-D field solver, this cuts the error roughly in half compared with Wheeler alone (see the table below).

Offset strip. The image method (Wadell §3.6.3) treats the strip as two virtual centred striplines, one with plate spacing 2h1+t2h_1 + t and one with 2h2+t2h_2 + t, and adds their capacitances: Z0=2Z1Z2/(Z1+Z2)Z_0 = 2Z_1Z_2/(Z_1+Z_2). It is exact when the strip is centred. It always overestimates Z0Z_0 as the strip moves toward one plane, because the two halves' fringing fields interact. The calculator states how large that error is (see below).

Losses. Dielectric loss is exact for a homogeneous TEM line: αd=πfεrtan⁡δ/c\alpha_d = \pi f\sqrt{\varepsilon_r}\tan\delta/c. Conductor loss uses Wheeler's incremental-inductance rule, αc=Rs2ηZ0∂Z0∂n\alpha_c = \frac{R_s}{2\eta Z_0}\frac{\partial Z_0}{\partial n}. The derivative is evaluated numerically by receding every metal surface by dndn, so the same rule also covers the offset geometry. For the centred line it agrees with Pozar's closed form to within about 1–5 %.

Higher-order mode. The first TE mode, which has a field variation across the strip, cuts off at fc=c/[2εr (W+πb/4)]f_c = c/\left[2\sqrt{\varepsilon_r}\,(W + \pi b/4)\right] (Pozar §3.7). An offset stripline can also excite the parallel-plate mode between the planes at any frequency, which is why stripline cavities are via-fenced.

How to use solve-for

Click ⇄ Solve next to Strip width and enter a target impedance to design a trace. You can also solve for the plate spacing bb (useful when choosing a prepreg) or back out εr\varepsilon_r from a TDR measurement of Z0Z_0 or delay. In the offset geometry, h1h_1 is held fixed while solving for bb, so the extra thickness goes into the gap above the strip.

Worked example

RO4350B-type laminate with εr=3.66\varepsilon_r = 3.66 and tan⁡δ=0.0037\tan\delta = 0.0037. Plate spacing b=0.5b = 0.5 mm, W=0.25W = 0.25 mm, half-ounce copper (t=17.5 μt = 17.5\,\mum), at 10 GHz, centred (the calculator defaults):

  • Z0=48.503Z_0 = 48.503 Ω, delay 162.09 ps/in, C′=3.3418C' = 3.3418 pF/in and L′=7.8618L' = 7.8618 nH/in.
  • Conductor loss 0.2064 dB/in and dielectric loss 0.1637 dB/in, so 0.3701 dB/in in total.
  • Guided wavelength 15.670 mm. The TE-mode cutoff is 121.91 GHz, far above the operating frequency.
  • Solving for exactly 50 Ω gives W=0.2356W = 0.2356 mm.

Now switch to Offset with h1=0.15h_1 = 0.15 mm, so the strip is 0.15 mm above the lower plane and 0.3325 mm below the upper one. Z0Z_0 drops to 44.453 Ω, and a 50 Ω line needs W=0.2002W = 0.2002 mm. At this position (strip centre at 32 % of bb from the nearer plane) the calculator notes that the image method reads about 0.5–2.5 % high, so check the final width with a field solver.

Accuracy and validity

The table compares the models with an independent 2-D finite-volume field solver (tooling/validation/laplace2d.py). That solver agrees with Cohn's exact solution to better than 0.05 %.

CaseModel error vs. field solver
Centred, t=0t = 0exact (Cohn)
Centred, t/b≤0.1t/b \le 0.1, 0.15≤W/b≤30.15 \le W/b \le 3−0.15 % … +0.03 %
Centred, t/b=0.2t/b = 0.2–0.30.3, W/b≈0.4W/b \approx 0.4–11−0.2 % … −0.6 %
Offset, strip near centre (h1/b≥0.4h_1/b \ge 0.4)+0.2 % … +0.6 %
Offset, h1/b=0.3h_1/b = 0.3+0.8 % (W/b = 2) … +2.3 % (narrow)
Offset, h1/b=0.2h_1/b = 0.2+1.6 % (W/b = 2) … +5.5 % (narrow)
Offset, h1/b=0.1h_1/b = 0.1+2.2 % (W/b = 2) … +11 % (W/b = 0.1)

The calculator warns when the strip centre is within 25 % of bb of either plane (and notes the error band up to 40 %), and when t/b>0.25t/b > 0.25. Conductor loss assumes smooth copper. Roughness adds 10–50 % at multi-GHz frequencies, depending on the foil.

Practical notes

  • The dielectric is not uniform in a real board. Core and prepreg usually have different εr\varepsilon_r, and resin-rich prepreg around the trace lowers the local value. Use the stack-up's effective Dk, or a field solver for a mixed dielectric.
  • Etch factor. Traces etch to a trapezoid. A common first-order fix is to enter the average of the top and bottom widths.
  • Thickness matters more in thin stack-ups. At b=0.2b = 0.2 mm, going from ½ oz to 1 oz copper changes Z0Z_0 by several ohms.
  • Via fences. In offset stripline and around discontinuities, stitch the two planes with vias spaced well under λg/10\lambda_g/10. Otherwise energy leaks into the parallel-plate mode.
  • Loss budget. Inner-layer loss is usually dominated by the dielectric at high frequency (it grows as ff), while conductor loss grows as f\sqrt f. Low-loss laminates pay off quickly above a few GHz.

References

  1. S. B. Cohn, “Characteristic Impedance of the Shielded-Strip Transmission Line,” IRE Trans. Microwave Theory Tech., vol. MTT-2, no. 2, pp. 52–57, July 1954.
  2. H. A. Wheeler, “Transmission-Line Properties of a Strip Line Between Parallel Planes,” IEEE Trans. Microwave Theory Tech., vol. MTT-26, no. 11, pp. 866–876, Nov. 1978.
  3. H. A. Wheeler, “Formulas for the Skin Effect,” Proc. IRE, vol. 30, no. 9, pp. 412–424, Sept. 1942 (incremental-inductance rule).
  4. B. C. Wadell, Transmission Line Design Handbook, Artech House, 1991, §3.6.3 (off-centre stripline, image method).
  5. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, §3.7 (stripline attenuation and higher-order modes).

This calculator's results are checked against 16 independent reference values in automated tests on every change. How we check accuracy.