Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Wavelength Calculator (Frequency to Wavelength, Electrical Length)

Convert frequency to free-space and in-medium wavelength, get electrical length in degrees, time delay, and λ/4 and λ/2 lengths for any εr or velocity factor.

3 cited sources31 reference checksRuns in your browser

Inputs

1 for air/vacuum. For a microstrip use the effective permittivity εeff, not the laminate εr.

Used for the electrical length and the time delay.

Results

Free-space wavelength(λ₀)
122.36
Wavelength in medium(λ)
122.36
Electrical length of ℓ(θ)
88.261
Time delay of ℓ(τ)
100.07
Quarter wavelength in medium(λ/4)
30.591
Half wavelength in medium(λ/2)
61.182
Delay per unit length(τ/ℓ)
84.725
Velocity factor(VF)
1
Equivalent εr(εr)
1
Length in wavelengths(ℓ/λ)
0.2452
  • Assumes a non-magnetic (μr = 1), lossless, non-dispersive medium. For TEM lines VF = 1/√εr; for microstrip use εeff, and in waveguide the guided wavelength is longer than this.

Formulas

λ0=c0f,c0=299 792 458 m/s\lambda_0 = \frac{c_0}{f},\quad c_0 = 299\,792\,458\ \mathrm{m/s}λ=vpf=λ0εr=VF⋅λ0\lambda = \frac{v_p}{f} = \frac{\lambda_0}{\sqrt{\varepsilon_r}} = \mathrm{VF}\cdot\lambda_0θ=360∘ ℓλ,τ=ℓvp=ℓεrc0\theta = 360^\circ\,\frac{\ell}{\lambda},\qquad \tau = \frac{\ell}{v_p} = \frac{\ell\sqrt{\varepsilon_r}}{c_0}

What this calculator does

Almost every RF dimension is a fraction of a wavelength: quarter-wave stubs and transformers, half-wave dipoles, patch antennas, filter resonators, and the "λ/10 rule" for when a trace starts to behave like a transmission line. This calculator converts between frequency and wavelength and works out what a physical length means electrically:

  • the free-space wavelength λ0=c0/f\lambda_0 = c_0/f, with c0=299 792 458c_0 = 299\,792\,458 m/s (exact by the definition of the metre);
  • the wavelength in a medium, described either by its relative permittivity εr\varepsilon_r or by a velocity factor VF=vp/c0\mathrm{VF} = v_p/c_0;
  • the electrical length of a physical length ℓ, in degrees, and its time delay;
  • the λ/4 and λ/2 lengths in the medium, the delay per unit length, and the length in wavelengths.

In a non-magnetic medium, a wave travels at vp=c0/εrv_p = c_0/\sqrt{\varepsilon_r}, so

λ=λ0εr=VF⋅λ0,θ=360∘ℓλ,τ=ℓvp.\lambda = \frac{\lambda_0}{\sqrt{\varepsilon_r}} = \mathrm{VF}\cdot\lambda_0,\qquad \theta = 360^\circ\frac{\ell}{\lambda},\qquad \tau = \frac{\ell}{v_p}.

εr or velocity factor?

Use εr for a homogeneous dielectric, such as a stripline buried in a laminate, or a coax line filled with a known dielectric. Use the velocity factor for cables, where the datasheet usually quotes it directly: about 0.66 for solid polyethylene, 0.70 for PTFE, and 0.80–0.88 for foamed dielectrics. The two descriptions are related by VF=1/εr\mathrm{VF} = 1/\sqrt{\varepsilon_r}, and the calculator shows both.

For a microstrip or a coplanar line, the field is partly in air, so enter the effective permittivity εeff\varepsilon_\text{eff} from the microstrip calculator, not the laminate's εr\varepsilon_r. Using the laminate value makes a quarter-wave microstrip stub roughly 10–20 % too short.

How to use solve-for

  • Solve Frequency for Quarter wavelength to find the frequency at which an existing stub or slot is resonant.
  • Solve Physical length for Electrical length to find the length of a 90° or 45° line. Enter the target in degrees.
  • Solve Physical length for Time delay to size a delay line or to match the skew between two traces.
  • Solve Relative permittivity for Electrical length to back out εr (or εeff) from a measured resonance or phase.

Worked example

Wi-Fi in air. At 2.45 GHz the free-space wavelength is 122.36 mm, and a quarter wave is 30.59 mm. A 30 mm length is 88.26° long and delays the signal by 100.07 ps.

A stripline in FR-4. Change εr to 4.3, the frequency to 1 GHz and the length to 100 mm. The wavelength falls to 144.57 mm, so a quarter wave is 36.14 mm. The 100 mm line is 249.0° long with a delay of 691.7 ps, which is 175.7 ps/in, the familiar "about 170–180 ps per inch" rule for inner layers in FR-4.

Coax. Choose Velocity factor, enter 0.66 and 100 MHz. The wavelength in the cable is 1.979 m, against 2.998 m in free space, so a quarter-wave coax stub is 49.5 cm long, not 75 cm.

Accuracy and validity

The relations are exact for a lossless, non-dispersive, non-magnetic medium carrying a TEM wave, and the calculator's arithmetic is exact to floating-point precision. Real results depend on how well you know the medium:

SituationWhat to watch
PCB laminatesεr depends on frequency, resin content and glass weave; use the design Dk at your frequency
Microstrip, CPWUse εeff, which also rises slowly with frequency (dispersion)
Coax cablesVF tolerance is typically ±1–2 %; phase-matched cables are specified separately
WaveguideNot TEM: the guided wavelength is longer than λ0\lambda_0 and depends on the cut-off frequency
Lossy mediaAt high loss the phase constant differs slightly from ωμε\omega\sqrt{\mu\varepsilon}

A 1 % error in εr gives a 0.5 % error in wavelength and phase. Over a 10-wavelength line, that is already 18° of phase.

Practical notes

  • End effects. Open-ended stubs and dipoles are electrically longer than their physical length because of fringing fields. Real half-wave dipoles are cut about 2–5 % short, and microstrip open stubs need an end-correction length.
  • When is a trace "long"? A common rule is that interconnects longer than about λ/10 at the highest significant frequency (or with a delay longer than about 1/6 of the rise time) need transmission-line design: controlled impedance and termination.
  • Degrees to time. At any frequency, 360° is one period: 1 ns at 1 GHz, 100 ps at 10 GHz. Converting skew budgets to degrees makes phase-sensitive designs, such as I/Q and beamforming, easier to reason about.
  • Wavelength sets the scale of antennas and shields. Slots and seams in shielding start to radiate efficiently at about λ/2, so keep apertures well below λ/20 at the highest frequency of concern.

References

  1. BIPM, The International System of Units (SI Brochure), 9th ed., 2019 (c₀ = 299 792 458 m/s exactly).
  2. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, ch. 1–2 (plane waves, phase velocity and wavelength on transmission lines).
  3. S. Ramo, J. R. Whinnery and T. Van Duzer, Fields and Waves in Communication Electronics, 3rd ed., Wiley, 1994 (uniform plane waves in dielectrics).

This calculator's results are checked against 31 independent reference values in automated tests on every change. How we check accuracy.