Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

PCB Trace Width and Current Calculator (IPC-2221 / IPC-2152)

PCB trace width for a target current, maximum current and temperature rise per IPC-2221, with an IPC-2152 fit, plus resistance, voltage drop and power loss.

4 cited sources12 reference checksRuns in your browser

Inputs

Rise of the trace above ambient. 10 °C is a common conservative design value; 20–30 °C is often acceptable.

Finished copper. 1 oz/ft² ≈ 1.37 mil ≈ 34.8 µm. Outer layers gain plating, typically +0.5–1 oz.

Selects the IPC-2221 constant k (0.048 external, 0.024 internal).

Annealed copper (IACS) is 58.0 MS/m. Electroplated copper can be 10–20 % lower.

Results

Required width (IPC-2221)(W_req)
30.944
Max current at W (IPC-2221)(I_max)
1.9332
Temperature rise at I (IPC-2221)(ΔT)
10.803
Power loss(P)
140.33
Required width (IPC-2152 fit, external)(W_req,2152)
36.628
Max current at W (IPC-2152 fit, external)
1.7669
Temperature rise at I (IPC-2152 fit, external)
12.812
Cross-section(A)
40.453
Trace temperature (IPC-2221)(T)
35.803
Resistance at trace temperature(R)
35.083
Voltage drop(V)
70.165
  • IPC-2221 is a fit to 1950s NBS chart data. Its internal-layer rule (half the external current) is very conservative: IPC-2152 found internal traces run about as cool as, or cooler than, external ones. For narrow external traces the IPC-2152 fit can predict a higher rise than IPC-2221, so compare both. Stack-up, nearby planes and copper pours change the real rise substantially.

Formulas

I=k ΔT0.44A0.725(A in mil2, k=0.048 ext, 0.024 int)I = k\,\Delta T^{0.44} A^{0.725}\quad (A\ \text{in mil}^2,\ k = 0.048\ \text{ext},\ 0.024\ \text{int})Wreq=1T(Ik ΔT0.44)1/0.725W_\text{req} = \frac{1}{T}\left(\frac{I}{k\,\Delta T^{0.44}}\right)^{1/0.725}ΔT2152=215.3 I2 W−1.15 T−1.0(W,T in mil, external)\Delta T_{2152} = 215.3\,I^2\,W^{-1.15}\,T^{-1.0}\quad (W, T\ \text{in mil, external})R=Lσ20WT[1+0.00393 (Ta+ΔT−20 ∘C)],V=IR,P=I2RR = \frac{L}{\sigma_{20} W T}\left[1 + 0.00393\,(T_a + \Delta T - 20\,^\circ\mathrm{C})\right],\quad V = IR,\quad P = I^2R

What this calculator does

A PCB trace carrying current dissipates I2RI^2R as heat. It warms until the heat it loses balances the heat it generates: by conduction into the laminate and planes, and by convection and radiation from the board surface. The designer's question is usually the reverse: how wide must this trace be so that it rises no more than ΔT above ambient? This calculator answers that question with two models and also gives the electrical consequences:

  • IPC-2221 (the classic equation), with the required width for a target current, the maximum current for a given width, and the temperature rise at a given current and width;
  • an IPC-2152-based estimate, from the closed-form fit Brooks and Adam made to the IPC-2152 external-trace charts, for comparison;
  • the resistance at the predicted trace temperature, the voltage drop and the power loss over the trace length.

IPC-2221

IPC-2221 (and IPC-D-275 and MIL-STD-275 before it) reproduces charts that go back to a 1956 National Bureau of Standards study. The curve fit printed in the standard is

I=k ΔT0.44 A0.725I = k\,\Delta T^{0.44}\,A^{0.725}

with II in amperes, ΔT\Delta T in °C and the cross-section A=W⋅TA = W\cdot T in square mils. The constant is k=0.048k = 0.048 for external layers and k=0.024k = 0.024 for internal ones. The internal value is simply the external one halved. In the original work the internal charts were not measured; they were derived by assuming that inner traces cool worse.

IPC-2152 fit

IPC-2152 (2009) replaced those charts with new measurements. It publishes charts only, and they are copyrighted. Douglas Brooks and Johannes Adam digitised the external-trace curves and found that one equation fits the 2 oz and 3 oz data very closely:

ΔT=215.3 I2 W−1.15 T−1.0(W,T in mil)\Delta T = 215.3\,I^2\,W^{-1.15}\,T^{-1.0}\qquad (W, T \text{ in mil})

The calculator uses this equation, inverted where needed, for the "IPC-2152 fit, external" results. Their internal-trace fits have constants that vary with copper weight and width, so this calculator leaves them out. Brooks and Adam found that internal traces in the IPC-2152 data run slightly cooler than external ones, so the external fit is somewhat conservative for inner layers.

Resistance and loss

The DC resistance uses the 20 °C conductivity (58.0 MS/m for annealed copper, per IEC 60028) and the copper temperature coefficient α=0.00393\alpha = 0.00393 /°C. It is evaluated at Ta+ΔTT_a + \Delta T, where ΔT\Delta T is the IPC-2221 rise at your current:

R=Lσ20WT[1+0.00393 (Ta+ΔT−20 ∘C)]R = \frac{L}{\sigma_{20} W T}\left[1 + 0.00393\,(T_a + \Delta T - 20\,^\circ\mathrm{C})\right]

How to use solve-for

Required width and max current are direct outputs, so you rarely need to solve for them. Solve-for helps with the other inversions:

  • Click ⇄ Solve on Trace length and target Voltage drop to find how long a run can be for a given drop budget.
  • Solve Trace width for Temperature rise at I (IPC-2152 fit) to size a trace with the newer data.
  • Solve Copper thickness for Max current to see what copper weight a fixed width needs.

Worked example

An external 1 oz trace (T=1.37T = 1.37 mil =34.8 μ= 34.8\,\mum), 50 mm long, carries 2 A at 25 °C ambient with a 10 °C allowed rise.

QuantityResult
Required width, IPC-22210.786 mm (30.9 mil)
Required width, IPC-2152 fit (external)0.930 mm (36.6 mil)
Max current of a 0.75 mm trace, IPC-22211.93 A
Rise of a 0.75 mm trace at 2 A, IPC-2221 / IPC-2152 fit10.8 °C / 12.8 °C
Resistance at 35.8 °C, voltage drop, power35.08 mΩ, 70.2 mV, 140 mW

This example teaches two things. First, for a narrow external trace the newer IPC-2152 data predicts a higher rise than IPC-2221, so IPC-2221 is not conservative everywhere. Second, switch Layer to internal and IPC-2221 asks for 2.04 mm and predicts a 52 °C rise for the 0.75 mm trace. That reflects the factor-of-two assumption, not physics: modern data shows that inner traces next to planes cool about as well as outer ones.

Accuracy and validity

ModelRangeNotes
IPC-2221 equationUp to 35 A external (17.5 A internal), widths to 400 mil, ΔT 10–100 °C, 0.5–3 oz copper (the extent of the charts)A curve fit to old chart data that has been redrawn many times; the internal curve was derived, not measured
IPC-2152 fit (Brooks & Adam)External traces, curves for roughly 5–500 mil widthsA fit to digitised charts, good to chart-reading precision. The IPC-2152 test boards had no adjacent planes
ResistanceDC, uniform temperatureIgnores the temperature gradient along the trace and skin effect

The calculator warns when your inputs leave these ranges. It also warns when the trace temperature passes 105 °C or the typical 130 °C maximum operating temperature of FR-4.

Both models describe one isolated trace in still air, on a board of a particular size and material. A real board is often better than this. A solid plane 5–10 mil below a trace can lower its rise dramatically, because copper conducts heat roughly a thousand times better than FR-4. It can also be worse: many parallel traces heat each other, and boards in sealed enclosures or in vacuum lose the convective cooling. Brooks and Adam conclude that trace temperatures depend on too many variables for any chart, and that critical cases need thermal simulation.

Practical notes

  • Use the finished thickness. Outer layers are usually plated up, and a "½ oz + plating" outer layer often ends up near 1.4–2 mil. Inner layers stay at foil thickness, and fabricators may etch them thinner.
  • Etching narrows the trace. The copper cross-section is a trapezoid whose top is narrower than the drawn width by roughly the copper thickness. Size fine traces with margin.
  • Long thin sections are the risk. A short neck-down at a pad or via has a lower current rating than the trace, but the copper around it sinks its heat. A long thin section has no such help.
  • Electroplated copper conducts worse. Plated copper can have 10–20 % higher resistivity than the 58 MS/m annealed standard. Lower Copper conductivity to see the effect on drop and loss.
  • Pulses heat less. These are steady-state models, and a short pulse heats a trace much less than the same DC current would. Use the RMS current for repetitive waveforms, but check the fusing limit for single high-energy events.

References

  1. IPC-2221B, Generic Standard on Printed Board Design, IPC, 2012, §6.2 and Fig. 6-4 (conductor current-carrying capacity).
  2. IPC-2152, Standard for Determining Current Carrying Capacity in Printed Board Design, IPC, 2009.
  3. D. G. Brooks and J. Adam, “Trace Currents and Temperatures Revisited,” UltraCAD Design, Inc., April 2015 (edit 7/2015), Eq. 3-2 and Table 3-1.
  4. IEC 60028, International Standard of Resistance for Copper, 1925 (ρ₂₀ = 1/58 Ω·mm²/m, α₂₀ = 0.00393 /°C).

This calculator's results are checked against 12 independent reference values in automated tests on every change. How we check accuracy.