Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Microstrip Patch Antenna Calculator

Rectangular microstrip patch design: width, length, fringing ΔL, edge resistance, inset-feed depth for 50 Ω, directivity and bandwidth (Balanis).

4 cited sources29 reference checksRuns in your browser

Inputs

Use the design Dk at the operating frequency (e.g. RT/duroid 5880: 2.20, RO4003C: 3.55, FR-4: ≈4.3).

Resistance wanted at the inset feed point, normally the feed-line impedance.

Results

Patch width(W)
40.563
Patch length(L)
32.055
Inset-feed depth for target R(y₀)
11.646
Edge input resistance(R_in(0))
288.48Ω
Effective permittivity(εreff)
3.3335
Length extension (each edge)(ΔL)
28.634
Effective length(L_eff)
33.51
Slot conductance(G₁)
1.138
Mutual slot conductance(G₁₂)
595.27
Directivity (dBi)(D)
6.37dB
Bandwidth (SWR ≤ 2, lossless)(BW)
1.21%
Surface-wave radiation efficiency(e_r^hed)
91.65%
  • Bandwidth and efficiency ignore conductor and dielectric loss; a lossy substrate (e.g. FR-4) gives a wider but less efficient patch.

Formulas

W=c2fr2εr+1,εreff=εr+12+εr−12(1+12hW)−1/2W = \frac{c}{2f_r}\sqrt{\frac{2}{\varepsilon_r+1}},\qquad \varepsilon_{\mathrm{reff}} = \frac{\varepsilon_r+1}{2} + \frac{\varepsilon_r-1}{2}\left(1+12\frac{h}{W}\right)^{-1/2}ΔLh=0.412 (εreff+0.3)(W/h+0.264)(εreff−0.258)(W/h+0.8),L=c2frεreff−2ΔL\frac{\Delta L}{h} = 0.412\,\frac{(\varepsilon_{\mathrm{reff}}+0.3)(W/h+0.264)}{(\varepsilon_{\mathrm{reff}}-0.258)(W/h+0.8)},\qquad L = \frac{c}{2f_r\sqrt{\varepsilon_{\mathrm{reff}}}} - 2\Delta LG1=1120π2∫0π[sin⁡ ⁣(k0W2cos⁡θ)cos⁡θ]2sin⁡3θ dθG_1 = \frac{1}{120\pi^2}\int_0^\pi \left[\frac{\sin\!\left(\frac{k_0W}{2}\cos\theta\right)}{\cos\theta}\right]^2 \sin^3\theta\,d\thetaG12=1120π2∫0π[sin⁡ ⁣(k0W2cos⁡θ)cos⁡θ]2J0(k0Lsin⁡θ) sin⁡3θ dθG_{12} = \frac{1}{120\pi^2}\int_0^\pi \left[\frac{\sin\!\left(\frac{k_0W}{2}\cos\theta\right)}{\cos\theta}\right]^2 J_0(k_0L\sin\theta)\,\sin^3\theta\,d\thetaRin(0)=12(G1+G12),Rin(y0)=Rin(0)cos⁡2 ⁣(πy0L)R_{in}(0) = \frac{1}{2(G_1+G_{12})},\qquad R_{in}(y_0) = R_{in}(0)\cos^2\!\left(\frac{\pi y_0}{L}\right)D=2 (k0W)2/I11+I12(k0Leff)/I1,I1=120π2G1D = \frac{2\,(k_0W)^2/I_1}{1 + I_{12}(k_0L_{\mathrm{eff}})/I_1},\qquad I_1 = 120\pi^2 G_1BW=1632 p c1εr hλ0 WL 1erhed,erhed=[1+3π4 k0hc1(1−1εr)3]−1\mathrm{BW} = \frac{16}{3\sqrt2}\,\frac{p\,c_1}{\varepsilon_r}\,\frac{h}{\lambda_0}\,\frac{W}{L}\,\frac{1}{e_r^{\mathrm{hed}}},\qquad e_r^{\mathrm{hed}} = \left[1+\frac{3\pi}{4}\,\frac{k_0h}{c_1}\left(1-\frac{1}{\varepsilon_r}\right)^3\right]^{-1}

What this calculator does

A rectangular microstrip patch is a metal rectangle of width WW and length LL on a grounded substrate of height hh and permittivity εr\varepsilon_r. Its fundamental TM₀₁₀ mode is a half-wave resonance along LL: the field under the patch reverses sign from one edge to the other, and the fringing fields at the two radiating edges (the edges of length WW) add in phase above the patch. The transmission-line model in Balanis, Antenna Theory §14.2, treats each radiating edge as a slot with conductance G1G_1 and susceptance B1B_1, joined by a low-impedance line of length LL.

This calculator follows the Balanis design procedure step by step:

  1. Width for efficient radiation: W=c2fr2εr+1W = \frac{c}{2f_r}\sqrt{\frac{2}{\varepsilon_r+1}}.
  2. Effective permittivity εreff\varepsilon_\text{reff} of a microstrip of width WW, which accounts for the part of the field that is in air.
  3. Length extension ΔL\Delta L (Hammerstad's open-end formula). Fringing makes each edge look electrically longer by ΔL\Delta L, so the physical length is L=c2frεreff−2ΔLL = \frac{c}{2f_r\sqrt{\varepsilon_\text{reff}}} - 2\Delta L.
  4. Slot conductances G1G_1 (self) and G12G_{12} (mutual), from Balanis' radiation integrals. The calculator evaluates them numerically with an adaptive Gauss–Kronrod integrator. The edge input resistance is Rin(0)=1/[2(G1+G12)]R_{in}(0) = 1/[2(G_1 + G_{12})].
  5. Inset-feed depth y0y_0. Moving the feed point a distance y0y_0 in from the radiating edge lowers the resistance as Rin(y0)=Rin(0)cos⁡2(πy0/L)R_{in}(y_0) = R_{in}(0)\cos^2(\pi y_0/L), so the depth that matches your target resistance is y0=Lπarccos⁡Rtarget/Rin(0)y_0 = \frac{L}{\pi}\arccos\sqrt{R_\text{target}/R_{in}(0)}.
  6. Directivity of the two-slot array, with the slots separated by the effective length Leff=L+2ΔLL_\text{eff} = L + 2\Delta L.
  7. Bandwidth and surface-wave efficiency from the closed-form CAD formulas of Jackson and Alexopoulos.

How to use solve-for

The design equations already give WW and LL directly from frf_r, so solve-for runs the other way round:

  • Frequency from a length. Solve Resonant frequency for a target Patch length to find where an existing patch resonates, for example after you trim a prototype or change the board.
  • Back-calculate εr. If a patch of known LL resonates off frequency, solve Substrate dielectric constant for that length to estimate the board's real εr\varepsilon_r at that frequency.
  • Substrate thickness for a bandwidth. Solve Substrate height for a target Bandwidth to see how thick the board must be to give, say, 3 % (SWR ≤ 2). Watch the h/λ0h/\lambda_0 warning as you do this.

Worked example

The defaults are a 2.45 GHz patch on 60-mil (1.524 mm) Rogers RO4003C, εr=3.55\varepsilon_r = 3.55, fed for 50 Ω. The calculator gives:

QuantityValue
Width WW40.563 mm
εreff\varepsilon_\text{reff}3.3335
ΔL\Delta L (each edge)0.7273 mm
Length LL32.055 mm
G1G_1 / G12G_{12}1.1380 mS / 0.59527 mS
Edge resistance Rin(0)R_{in}(0)288.48 Ω
Inset depth y0y_0 for 50 Ω11.646 mm
Directivity6.37 dBi
Bandwidth (SWR ≤ 2)1.21 % (about 30 MHz)
Surface-wave efficiency91.65 %

As a cross-check against the textbook, enter Balanis' Example 14.1: fr=10f_r = 10 GHz, εr=2.2\varepsilon_r = 2.2, h=1.588h = 1.588 mm. The calculator returns W=11.850W = 11.850 mm, εreff=1.9715\varepsilon_\text{reff} = 1.9715, ΔL=0.8110\Delta L = 0.8110 mm and L=9.0534L = 9.0534 mm, against the book's 11.86 mm, 1.972, 0.81 mm and 9.06 mm. (Balanis uses c=3×108c = 3\times10^8 m/s, which accounts for the 0.07 % difference.) For the same patch, Example 14.2 gives Rin(0)≈228R_{in}(0) \approx 228 Ω and y0=3.126y_0 = 3.126 mm; the calculator gives 228.40 Ω and 3.1236 mm. This case also raises the h/λ0h/\lambda_0 warning, since h=0.053 λ0h = 0.053\,\lambda_0.

Accuracy and validity

QuantityModelWhat to expect
WWBalanis design ruleA choice, not a prediction: widths near this value all work
LL, resonant frequencyTransmission-line model with Hammerstad ΔL\Delta LUsually within a few percent for h≤0.05λ0h \le 0.05\lambda_0; worse on thick boards
Rin(0)R_{in}(0)Two-slot conductance modelApproximate: feed and higher-order-mode effects are not modelled
y0y_0cos⁡2\cos^2 inset lawBest on thin, low-εr\varepsilon_r boards; the notch width also matters
DirectivityTwo-slot array over an infinite ground planeA finite ground plane changes it and adds back radiation
Bandwidth, efficiencyJackson–Alexopoulos CAD formulas, losslessThin-substrate fits; conductor and dielectric loss excluded

The model is a thin-substrate model. The calculator warns when h/λ0h/\lambda_0 exceeds 0.05: surface waves then take a growing share of the power, the probe or inset feed adds noticeable reactance, and the real resonance falls below the prediction. Above h/λ0=0.1h/\lambda_0 = 0.1 the result is flagged as invalid. Below h/λ0=0.003h/\lambda_0 = 0.003 the bandwidth becomes a fraction of a percent, and conductor and dielectric losses (which the bandwidth and efficiency figures here leave out) dominate.

The numerical integrals agree with an independent mpmath evaluation (Balanis' closed form for G1G_1 with the sine integral, and the full two-dimensional directivity integral) to better than 1 part in 10710^7 (see tooling/validation/patch_antenna_mpmath.py).

Practical notes

  • Use the right εr. The resonant frequency scales as 1/εreff1/\sqrt{\varepsilon_\text{reff}}, so a 2 % error in εr\varepsilon_r moves frf_r by about 1 %. That alone can exceed a 1.2 % bandwidth. Use the laminate's design Dk at your frequency, not the process Dk.
  • Lossy substrates. On FR-4 (tan⁡δ≈0.02\tan\delta \approx 0.02) dielectric loss widens the bandwidth and costs 1–3 dB of gain. The bandwidth shown here assumes lossless materials, so on FR-4 it is a lower bound.
  • Inset notch. Cut the notch on each side of the feed line about one feed-line width wide. A very narrow notch adds capacitance and shifts both frf_r and the match.
  • Edge impedance above the target is normal. Typical values are 150–300 Ω. If your target is above Rin(0)R_{in}(0), no inset depth exists; use a quarter-wave transformer at the edge instead.
  • Tune with one prototype. Even a perfect model is off by the board's Dk tolerance. Build one patch, measure frf_r, then use solve-for on εr\varepsilon_r to calibrate and redesign.
  • Keep W below 2L so the TM₀₂₀ mode stays well above the operating band. The Balanis width gives W/L≈1.3W/L \approx 1.3–1.5 on common substrates.

References

  1. C. A. Balanis, Antenna Theory: Analysis and Design, 4th ed., Wiley, 2016, §14.2 (rectangular patch: transmission-line model, slot conductances, inset feed, directivity).
  2. E. O. Hammerstad, “Equations for Microstrip Circuit Design,” Proc. 5th European Microwave Conf., Hamburg, 1975, pp. 268–272 (open-end extension ΔL).
  3. D. R. Jackson and N. G. Alexopoulos, “Simple Approximate Formulas for Input Resistance, Bandwidth, and Efficiency of a Resonant Rectangular Patch,” IEEE Trans. Antennas Propag., vol. 39, no. 3, pp. 407–410, Mar. 1991.
  4. D. R. Jackson, “Overview of Microstrip Antennas,” short-course notes, Dept. of ECE, University of Houston (CAD formulas for p, c1, radiation efficiency and bandwidth).

This calculator's results are checked against 29 independent reference values in automated tests on every change. How we check accuracy.