Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

RF Link Budget Calculator

Full RF link budget: EIRP, free-space path loss, received power, kTB noise floor with noise figure, SNR or Eb/N0, link margin and maximum range.

5 cited sources17 reference checksRuns in your browser

Inputs

Sum of everything beyond free space: fade margin, rain, polarization mismatch, pointing, body loss, implementation loss.

Loss between the antenna and the first amplifier, assumed at 290 K. It reduces the signal and adds thermal noise.

290 K for a terrestrial antenna seeing the ground (gives the classic kT₀B·F floor); 30–100 K for a dish pointed at clear sky.

Results

Link margin(M)
12.903dB
Received power (Rx input)(P_r)
−86.073
Signal-to-noise ratio(SNR)
22.903dB
Maximum range (0 dB margin)(d_max)
8.834
EIRP(EIRP)
25
Free-space path loss(L_fs)
106.07dB
Noise floor (Rx input)(N)
−108.98
Receiver sensitivity(S_min)
−98.975
System noise temperature (at antenna)(T_sys)
1154.5K
C/N₀ (dB-Hz)(C/N₀)
82.903dB
Required SNR in B(SNR_req)
10dB
  • Free-space propagation only. Ground reflection, obstructions and multipath (two-ray, Hata, ITU-R P.1411) can add tens of dB; budget them in the extra-loss field.

Formulas

EIRP=Pt−Ltx+Gt,Lfs=20log⁡10 ⁣(4πdfc)\mathrm{EIRP} = P_t - L_{tx} + G_t,\qquad L_{fs} = 20\log_{10}\!\left(\frac{4\pi d f}{c}\right)Pr=EIRP−Lfs−Lx+Gr−Lrx(dB)P_r = \mathrm{EIRP} - L_{fs} - L_x + G_r - L_{rx}\quad(\mathrm{dB})Tsys=TA+(Lrx−1)T0+Lrx(F−1)T0,N=k Tsys BLrx  =TA=T0  kT0BFT_{sys} = T_A + (L_{rx}-1)T_0 + L_{rx}(F-1)T_0,\qquad N = \frac{k\,T_{sys}\,B}{L_{rx}} \;\overset{T_A=T_0}{=}\; kT_0BFkT0=−173.98 dBm/Hz,SNR=Pr−N,CN0=SNR+10log⁡10BkT_0 = -173.98\ \mathrm{dBm/Hz},\qquad \mathrm{SNR} = P_r - N,\qquad \frac{C}{N_0} = \mathrm{SNR} + 10\log_{10}BSNRreq=EbN0+10log⁡10RbB,M=SNR−SNRreq,dmax=d⋅10M/20\mathrm{SNR}_{req} = \frac{E_b}{N_0} + 10\log_{10}\frac{R_b}{B},\qquad M = \mathrm{SNR}-\mathrm{SNR}_{req},\qquad d_{max} = d\cdot 10^{M/20}

What this calculator does

A link budget adds up every gain and loss between a transmitter and a receiver, in decibels, and compares the resulting signal-to-noise ratio with what the demodulator needs. The difference is the link margin: how many dB the link can lose to fading, misalignment or ageing before it fails.

The calculator follows the signal from end to end:

  1. EIRP =Pt−Ltx+Gt= P_t - L_{tx} + G_t, the power an isotropic radiator would need to give the same field in the main beam.

  2. Free-space path loss Lfs=20log⁡10(4πdf/c)L_{fs} = 20\log_{10}(4\pi d f/c) (Friis). Everything else in the path (fade margin, rain, polarization, pointing, implementation loss) goes in the single extra losses term LxL_x.

  3. Received power at the receiver input, after the receive antenna gain and the receive feed loss: Pr=EIRP−Lfs−Lx+Gr−LrxP_r = \text{EIRP} - L_{fs} - L_x + G_r - L_{rx}.

  4. Noise floor. The receive chain is treated as a cascade: the antenna at noise temperature TAT_A, a lossy feed at the standard temperature T0=290T_0 = 290 K, then a receiver of noise figure FF. Referred to the antenna terminals, the system temperature is

    Tsys=TA+(Lrx−1) T0+Lrx(F−1) T0,T_{sys} = T_A + (L_{rx}-1)\,T_0 + L_{rx}(F-1)\,T_0,

    and the noise power at the receiver input is N=kTsysB/LrxN = kT_{sys}B/L_{rx}. With TA=290T_A = 290 K this reduces exactly to the familiar N=kT0BFN = kT_0BF, that is −173.98 dBm/Hz+10log⁡10B+NF-173.98\ \text{dBm/Hz} + 10\log_{10}B + \text{NF}, whatever the feed loss.

  5. SNR =Pr−N= P_r - N, and C/N0=SNR+10log⁡10BC/N_0 = \text{SNR} + 10\log_{10}B in dB-Hz.

  6. Requirement. Enter either the required SNR in bandwidth BB directly, or the required Eb/N0E_b/N_0 and the data rate RbR_b. The two are related by SNR=Eb/N0+10log⁡10(Rb/B)\text{SNR} = E_b/N_0 + 10\log_{10}(R_b/B).

  7. Margin M=SNR−SNRreqM = \text{SNR} - \text{SNR}_{req}, and the maximum range. In free space each 6.02 dB of margin doubles the distance, so dmax=d⋅10M/20d_{max} = d\cdot10^{M/20}.

How to use solve-for

Every term is in dB, so the budget can be inverted on any of its knobs:

  • Distance for a target margin. Solving for 0 dB margin gives the same value as the Maximum range output. A positive target, such as 10 dB, gives a range with fade margin built in.
  • Transmit power for a target margin or SNR. This is the minimum PA output that closes the link.
  • Tx or Rx antenna gain for a target margin. This tells you how big the antennas must be.
  • Noise figure for a target margin or SNR, to see how good the LNA must be.

Worked example

The defaults are a 2.4 GHz link over 2 km: 20 dBm into a 1 dB cable and a 6 dBi antenna at each end, 10 dB of extra loss and fade margin, a 5 dB noise-figure receiver behind 1 dB of cable, 1 MHz of noise bandwidth and a required SNR of 10 dB.

LineValue
EIRP25 dBm
Free-space path loss106.07 dB
Received power−86.073 dBm
System noise temperature1154.5 K
Noise floor−108.98 dBm
SNR22.903 dB
C/N0C/N_082.903 dB-Hz
Receiver sensitivity (SNR = 10 dB)−98.975 dBm
Link margin12.903 dB
Maximum range8.834 km

The noise floor is −173.98+60+5=−108.98-173.98 + 60 + 5 = -108.98 dBm. The 1 dB receive cable does not appear in it, because a 290 K attenuator in front of a 290 K source adds exactly as much noise as it removes. It still costs 1 dB of signal. To run the link with only 6 dB of margin, solve Transmit power for a margin of 6 dB: 13.097 dBm is enough.

Switch Requirement given as to Eb/N0E_b/N_0 with 9.6 dB (uncoded BPSK at a BER of 10−510^{-5}) and 250 kbit/s. The required SNR in the 1 MHz bandwidth drops to 3.5794 dB, the available Eb/N0E_b/N_0 is 28.923 dB, the margin becomes 19.323 dB, and the maximum range grows to 18.501 km.

Accuracy and validity

The budget arithmetic is exact. The calculator is checked against analytic values (−173.975 dBm/Hz at 290 K, −113.975 dBm in 1 MHz) and against two published budgets: Sklar's 8 GHz satellite uplink (margin 8.0 dB, TS=4106T_S = 4106 K) and the ADS-B example in PySDR (SNR 35.1 dB). The limits are those of the inputs:

AssumptionEffect when it fails
Free-space propagationGround reflection, terrain and buildings add loss that grows faster than 20log⁡10d20\log_{10}d. The maximum range then overestimates.
One lumped extra-loss termLosses that depend on distance, such as rain or gas attenuation in dB/km, do not scale in the range extrapolation.
Feed at 290 KA hot or cryogenic feed changes TsysT_{sys}. For a cooled front end, fold the feed into TAT_A.
BB is the noise bandwidthUse the receiver's equivalent noise bandwidth, not the occupied bandwidth. For root-raised-cosine filtering it equals the symbol rate.
Thermal noise onlyInterference, phase noise and adjacent-channel leakage are not included.

Practical notes

  • Fade margin depends on the environment. Line-of-sight microwave links typically carry 20–40 dB for 99.99 % availability, depending on path length and climate. Short indoor links need 10–20 dB for Rayleigh fading. Put this in the extra-loss term.
  • Antenna temperature. A dish pointed at clear sky sees 20–60 K, not 290 K. Entering the real TAT_A for a satellite downlink can gain several dB over the kT0BFkT_0BF approximation.
  • Include implementation loss. Real modems need 1–3 dB more than the theoretical Eb/N0E_b/N_0. Add it to the requirement or to the extra losses.
  • Coding gain lowers the required Eb/N0E_b/N_0: about 5–7 dB for good convolutional or LDPC codes at a BER of 10−510^{-5}. Enter the coded requirement, and use the information bit rate for RbR_b.
  • Check EIRP limits. Regulations limit EIRP, not transmit power. In many regions the 2.4 GHz ISM band allows 20 dBm (100 mW) EIRP in Europe and up to 36 dBm EIRP point-to-multipoint in the US. A high-gain antenna can therefore push you over the limit.

References

  1. H. T. Friis, “A Note on a Simple Transmission Formula,” Proc. IRE, vol. 34, no. 5, pp. 254–256, May 1946.
  2. H. T. Friis, “Noise Figures of Radio Receivers,” Proc. IRE, vol. 32, no. 7, pp. 419–422, July 1944.
  3. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, ch. 10 (noise temperature, lossy-line noise) and ch. 14 (link budget).
  4. B. Sklar, Digital Communications: Fundamentals and Applications, 2nd ed., Prentice Hall, 2001, ch. 5 (link analysis).
  5. IEEE Std 100, The Authoritative Dictionary of IEEE Standards Terms, 7th ed., 2000 (standard noise temperature T0 = 290 K).

This calculator's results are checked against 17 independent reference values in automated tests on every change. How we check accuracy.