Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Impedance Matching Network Calculator (L, Pi, T)

Design lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.

3 cited sources21 reference checksRuns in your browser

Inputs

Series form: ZL = RL + jXL. Negative = capacitive.

Results

Shunt element across the source port: capacitor(C₁)
6.1259
Series element on the load side: inductor(L₃)
7.3654
Shunt element across the source port: reactance(X₁)
−28.868
Series element on the load side: reactance(X₃)
41.651
Network loaded Q(Q)
1.732
Estimated 3-dB bandwidth (f/Q)(BW)
519.62

Formulas

Zin=Zs∗(conjugate match)Z_\mathrm{in} = Z_s^{*}\quad(\text{conjugate match})Shunt at load: (BL+B)2=GLRs−GL2,X=−Xs+BL+BGL2+(BL+B)2\text{Shunt at load: } (B_L + B)^2 = \frac{G_L}{R_s} - G_L^2,\quad X = -X_s + \frac{B_L+B}{G_L^2 + (B_L+B)^2}Series at load: (XL+X)2=RLGt−RL2,B=Bt+XL+XRL2+(XL+X)2,  Gt+jBt=1Zs∗\text{Series at load: } (X_L + X)^2 = \frac{R_L}{G_t} - R_L^2,\quad B = B_t + \frac{X_L+X}{R_L^2 + (X_L+X)^2},\ \ G_t + jB_t = \frac{1}{Z_s^*}Π: Rv=max⁡(Rs,RL)Q2+1,T: Rv=min⁡(Rs,RL) (Q2+1),Qmin=RmaxRmin−1\Pi:\ R_v = \frac{\max(R_s,R_L)}{Q^2+1},\qquad T:\ R_v = \min(R_s,R_L)\,(Q^2+1),\qquad Q_\mathrm{min} = \sqrt{\frac{R_\mathrm{max}}{R_\mathrm{min}}-1}L=Xω,C=−1ωX,BW3 dB≈f0QL = \frac{X}{\omega},\quad C = \frac{-1}{\omega X},\qquad \mathrm{BW}_{3\,\mathrm{dB}} \approx \frac{f_0}{Q}

What this calculator does

A matching network is a lossless arrangement of inductors and capacitors placed between a source and a load so that the source sees the complex conjugate of its own impedance, Zin=Zs∗Z_\text{in} = Z_s^*. That is the condition for maximum power transfer. For a lossless network it also means the load sees ZL∗Z_L^* looking back toward the source. The calculator designs three classic lumped networks:

  • the L-network (two elements). For a given ZsZ_s and ZLZ_L there are two solutions, and the calculator gives both;
  • the Pi network (shunt, series, shunt) and the T network (series, shunt, series), where you choose the loaded QQ and so set the bandwidth.

Enter the source and the load as series resistance and reactance (Z=R+jXZ = R + jX, with negative XX for a capacitive part). For each element, the results give its reactance and its inductance or capacitance at the design frequency. Each label tells you whether the element is in series or in shunt, and where it sits: on the source side, in the middle, or on the load side.

The L-network

Pozar (§5.1) uses two L-section shapes. When the load resistance is at least the source resistance (RL≥RsR_L \ge R_s), the shunt element goes across the load and the series element sits on the source side. Otherwise the series element sits next to the load and the shunt element goes across the source. The calculator picks the shape that is always realisable. Within that shape, the quadratic for the shunt susceptance (or series reactance) has two roots. These are solution 1 and solution 2. One is usually low-pass (series L, shunt C) and the other high-pass. With a reactive load, the absorbed reactance can make an element switch type.

Once RsR_s and RLR_L are fixed, so is the L-network's Q. For resistive terminations it is Q=Rmax/Rmin−1Q = \sqrt{R_\text{max}/R_\text{min}-1} (Bowick Eq. 4-1). For complex terminations, the calculator reports the node Q at the shunt element, ∣Bnode∣/G|B_\text{node}|/G or ∣Xnode∣/R|X_\text{node}|/R.

Pi and T networks

A Pi network is two L-sections back to back. Each one transforms its termination down to a "virtual" resistance RvR_v in the middle, and the two series arms combine into one element. Bowick defines the loaded Q through the larger termination:

Rv=max⁡(Rs,RL)Q2+1.R_v = \frac{\max(R_s,R_L)}{Q^2+1}.

The T network is the dual. Both terminations are transformed up to Rv=min⁡(Rs,RL)(Q2+1)R_v = \min(R_s,R_L)(Q^2+1), and the two shunt arms combine. A Pi or T network exists only when QQ is larger than the L-network's Q, Qmin=Rmax/Rmin−1Q_\text{min} = \sqrt{R_\text{max}/R_\text{min}-1}. Below that the calculator warns you and reports the minimum. At exactly QminQ_\text{min}, one shunt (Pi) or series (T) element disappears, and the network becomes an L-network. The Pi/T form selector chooses the low-pass form (series inductors, shunt capacitors, which also filters harmonics) or the high-pass form (series capacitors, which also block DC).

The bandwidth estimate is BW3 dB≈f0/Q\mathrm{BW}_{3\,\text{dB}} \approx f_0/Q. It is a good guide for Q≳3Q \gtrsim 3 and only a rough one for lower Q.

Worked example

Match a transistor input of ZL=12.5−j20 ΩZ_L = 12.5 - j20\ \Omega to a 50 Ω source at 900 MHz (the defaults).

L-network, solution 1: the load resistance is lower than the source resistance, so the series element is on the load side. The calculator gives a series inductor of 7.3654 nH (+41.651 Ω, which includes the 20 Ω needed to cancel the load's capacitive reactance) and a shunt capacitor of 6.1259 pF (−28.868 Ω) across the source. The network Q is 1.7321, so the estimated bandwidth is 519.62 MHz.

Solution 2: a series capacitor of 107.13 pF (−1.6506 Ω) at the load and a shunt inductor of 5.1049 nH (+28.868 Ω) across the source. The Q is the same. This version blocks DC, but the 107 pF part is almost a short at 900 MHz, so its self-resonance matters.

Pi, low-pass, Q = 5: Rv=1.9231R_v = 1.9231 Ω. The network is a shunt 17.684 pF across the source, a series 3.3005 nH, and a shunt 12.340 pF across the load. The bandwidth estimate drops to 180 MHz.

Solving and sweeping

There are no solve-for targets here, because the outputs are the element values themselves. To design for a bandwidth, set Q=f0/BWQ = f_0/\text{BW} directly. Use Sweep & plot on the frequency to see how the component values scale. The reactances do not depend on frequency, so L∝1/fL \propto 1/f and C∝1/fC \propto 1/f.

Accuracy and validity

ItemAccuracy
Element reactances (ideal L and C)Exact: the network presents Zs∗Z_s^* to better than 10−910^{-9} (checked by an independent cascade over random complex terminations)
Pozar Ex. 5.1 and Bowick Ex. 4-4/4-5Reproduced within the books' rounding (≤ 1 %)
Bandwidth f0/Qf_0/QApproximation, best for Q≳3Q \gtrsim 3
Real componentsNot modelled: parasitics, self-resonance, finite QuQ_u

The calculator warns about inductors below about 0.5 nH and capacitors below about 0.3 pF, which are comparable to pad parasitics. It also warns about Q above 20, where component loss becomes significant (loss grows roughly as Q/QuQ/Q_u, where QuQ_u is the components' unloaded Q).

Practical notes

  • Absorb the parasitics. If the load has a 0.5 pF package capacitance in shunt, subtract it from the calculated shunt capacitor rather than adding a separate element (Bowick's approach).
  • Pick the solution for the job: low-pass to suppress harmonics after a power amplifier, high-pass or series-C to block DC bias, and the one with the most practical component values otherwise.
  • Complex source. Enter the real output impedance of the driving stage. The network matches to its conjugate, not to its value.
  • Check self-resonance. Every chip inductor and capacitor must have a self-resonant frequency well above f0f_0, usually at least twice it.
  • Multi-section for bandwidth. If the L-network's Q is already too high for the bandwidth you need, cascade L-sections through intermediate resistances (geometric steps) to lower the Q.

References

  1. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, §5.1 “Matching with Lumped Elements (L Networks),” Eqs. (5.3)–(5.6).
  2. C. Bowick, RF Circuit Design, Newnes (H. W. Sams), 1982, ch. 4 “Impedance Matching” (L, Pi and T networks; Eqs. 4-1, 4-4, 4-5).
  3. R. Ludwig and G. Bogdanov, RF Circuit Design: Theory and Applications, 2nd ed., Pearson, 2009, §8.1–8.2 (matching networks, node quality factor and bandwidth).

This calculator's results are checked against 21 independent reference values in automated tests on every change. How we check accuracy.