Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

Attenuator Calculator (Pi, T, Bridged-T, L-Pad)

Resistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.

3 cited sources41 reference checksRuns in your browser

Inputs

Power loss between matched source and load. For unequal impedances it must be at least the minimum loss.

Equal to Z₁ for a symmetrical pad.

Power delivered into the pad's input (equal to the available source power, since the pad is matched).

Results

R1: shunt, input side(R1)
96.248
R2: series(R2)
71.151
R3: shunt, output side(R3)
96.248
Power delivered to the load(Pout)
100
Total power dissipated in the pad(Pdiss)
900
Power in R1(P(R1))
519.49
Power in R2(P(R2))
328.56
Power in R3(P(R3))
51.949
R1, nearest standard value(R1std)
95.3
R2, nearest standard value(R2std)
71.5
R3, nearest standard value(R3std)
95.3
Attenuation with standard values(A′)
10.07dB
Input return loss with standard values(RL₁)
53.8dB
Output return loss with standard values(RL₂)
53.8dB
  • R1 dissipates the most power: 519 mW (51.9 % of the input). Derate its power rating for temperature.

Formulas

N=10A/10,K=NN = 10^{A/10},\quad K = \sqrt{N}Π (Z0): Rshunt=Z0K+1K−1,Rseries=Z0K2−12K\Pi\ (Z_0):\ R_\mathrm{shunt} = Z_0\frac{K+1}{K-1},\quad R_\mathrm{series} = Z_0\frac{K^2-1}{2K}T (Z0): Rseries=Z0K−1K+1,Rshunt=Z02KK2−1T\ (Z_0):\ R_\mathrm{series} = Z_0\frac{K-1}{K+1},\quad R_\mathrm{shunt} = Z_0\frac{2K}{K^2-1}Bridged-T: Rbridge=Z0(K−1),Rshunt=Z0K−1\text{Bridged-T}:\ R_\mathrm{bridge} = Z_0(K-1),\quad R_\mathrm{shunt} = \frac{Z_0}{K-1}T (Z1≠Z2): R2=2NZ1Z2N−1,  R1=Z1N+1N−1−R2,  R3=Z2N+1N−1−R2T\ (Z_1\neq Z_2):\ R_2 = \frac{2\sqrt{N Z_1 Z_2}}{N-1},\ \ R_1 = Z_1\frac{N+1}{N-1}-R_2,\ \ R_3 = Z_2\frac{N+1}{N-1}-R_2Π (Z1≠Z2): R2=N−12Z1Z2N,  1R1=N+1Z1(N−1)−1R2,  1R3=N+1Z2(N−1)−1R2\Pi\ (Z_1\neq Z_2):\ R_2 = \frac{N-1}{2}\sqrt{\frac{Z_1Z_2}{N}},\ \ \frac{1}{R_1} = \frac{N+1}{Z_1(N-1)}-\frac{1}{R_2},\ \ \frac{1}{R_3} = \frac{N+1}{Z_2(N-1)}-\frac{1}{R_2}L (Zh>Zl): Rseries=Zh(Zh−Zl),  Rshunt=ZlZhZh−Zl,  Amin=20log⁡10 ⁣(r+r−1), r=ZhZlL\ (Z_h>Z_l):\ R_\mathrm{series} = \sqrt{Z_h(Z_h-Z_l)},\ \ R_\mathrm{shunt} = Z_l\sqrt{\frac{Z_h}{Z_h-Z_l}},\ \ A_\mathrm{min} = 20\log_{10}\!\left(\sqrt{r}+\sqrt{r-1}\right),\ r=\frac{Z_h}{Z_l}

What this calculator does

A resistive attenuator (a "pad") reduces signal power by a known amount while keeping both ports matched. The calculator designs the four common pads:

  • Pi: shunt R1, series R2, shunt R3. For unequal impedances, R1 and R3 differ.
  • T: series R1, shunt R2, series R3.
  • Bridged-T: two series arms equal to Z0Z_0, a shunt R3 from their junction, and a bridge R4 from input to output. Only two resistor values change with attenuation, which is why it suits variable attenuators.
  • Minimum-loss L-pad: the lowest-loss resistive network that matches two different impedances (for example 75 Ω to 50 Ω). Here the attenuation is an output, not an input.

The Pi and T pads accept different input and output impedances Z1Z_1 and Z2Z_2. A pad between unequal impedances cannot have less loss than the L-pad. The calculator reports that minimum and refuses lower values.

For every topology it also gives the power dissipated in each resistor for a given input power, and the nearest E24 or E96 values together with the attenuation and return loss you will actually get with them.

The equations

With N=10A/10N = 10^{A/10} and K=NK = \sqrt N, the symmetrical pads in a Z0Z_0 system are:

Π: Rshunt=Z0K+1K−1,Rseries=Z0K2−12K\Pi:\ R_\text{shunt} = Z_0\frac{K+1}{K-1},\quad R_\text{series} = Z_0\frac{K^2-1}{2K} T: Rseries=Z0K−1K+1,Rshunt=Z02KK2−1T:\ R_\text{series} = Z_0\frac{K-1}{K+1},\quad R_\text{shunt} = Z_0\frac{2K}{K^2-1} Bridged-T: Rbridge=Z0(K−1),Rshunt=Z0K−1\text{Bridged-T}:\ R_\text{bridge} = Z_0(K-1),\quad R_\text{shunt} = \frac{Z_0}{K-1}

For unequal impedances, the general T has a shunt arm 2NZ1Z2/(N−1)2\sqrt{NZ_1Z_2}/(N-1), and each series arm is Zi(N+1)/(N−1)Z_i(N+1)/(N-1) minus that shunt value. The Pi is the dual. Both are listed in the formulas panel. The minimum-loss L-pad between Zh>ZlZ_h > Z_l puts Zh(Zh−Zl)\sqrt{Z_h(Z_h-Z_l)} in series on the high side and ZlZh/(Zh−Zl)Z_l\sqrt{Z_h/(Z_h-Z_l)} in shunt on the low side, with

Amin=20log⁡10 ⁣(r+r−1),r=Zh/Zl.A_\text{min} = 20\log_{10}\!\left(\sqrt{r}+\sqrt{r-1}\right),\qquad r = Z_h/Z_l.

The limits are a useful sanity check. At 0 dB the series resistors go to 0 Ω and the shunt resistors to an open circuit. At very high attenuation, the Pi shunt and T series resistors approach Z0Z_0.

Solve-for

Click ⇄ Solve next to Attenuation and choose a resistor as the target. This shows the attenuation you get from a resistor you already have. For example, a 100 Ω bridge in a 50 Ω bridged-T gives 20log⁡10(3)=9.5420\log_{10}(3) = 9.54 dB. You can also solve the input power for a given power in one resistor. That is the fastest way to find the maximum input power when the hottest resistor is rated at, say, 0.25 W.

Worked example

A 10 dB Pi pad in a 50 Ω system with 1 W in (the defaults):

QuantityValue
R1 = R3 (shunt)96.248 Ω
R2 (series)71.151 Ω
Power in R1 (input shunt)0.51949 W
Power in R2 (series)0.32856 W
Power in R3 (output shunt)0.051949 W
Output power0.1 W

The input shunt resistor takes more than half of the input power, so it is the part to size: a 1 W pad needs a resistor rated at least 0.5 W after temperature derating. With E96 parts (95.3 Ω and 71.5 Ω), the pad gives 10.067 dB with 53.8 dB return loss at both ports. With E24 parts (100 Ω and 68 Ω), it gives 9.629 dB with 49.6 dB return loss. Both are better than most connectors.

Switch to Minimum-loss L-pad with Z1=75Z_1 = 75 Ω and Z2=50Z_2 = 50 Ω. The calculator gives a 43.301 Ω series resistor on the 75 Ω side, an 86.603 Ω shunt resistor on the 50 Ω side, and a loss of 5.7195 dB.

Accuracy and validity

The resistor values are exact for ideal resistors and real, frequency-independent terminations. The golden vectors reproduce the published 50 Ω pad tables and the exact rational values at 20 dB (K=10K = 10: 61.111 Ω and 247.5 Ω for the Pi). The actual behaviour depends on the parts:

EffectWhen it mattersMitigation
Resistor toleranceAlways: shifts the attenuation and the match by a few hundredths of a dB per percentUse the standard-value outputs to check
Pad and resistor parasiticsAbove about 1 GHz for 0603, 3 GHz for 0402Thin-film parts, small footprints, ground vias next to the shunt resistors
High attenuation in one stageAbove about 40 dB, stray coupling bypasses the padCascade two pads, shield, keep input and output apart
Power deratingChip resistors are rated at 70 °C ambientFollow the manufacturer's derating curve; spread the heat
Pulse powerPeak power can exceed the average ratingCheck the resistor's pulse-handling curve

Practical notes

  • Pi or T? In a 50 Ω system, the Pi uses higher shunt values and the T uses smaller series values. At high attenuation, the T's shunt resistor becomes very small (10.1 Ω at 20 dB), and its ground return inductance then limits the frequency range. The Pi is usually preferred in microstrip.
  • The resistor that dissipates the most depends on the attenuation. In a 50 Ω Pi, the series arm is hottest below about 6 dB and the input shunt above it. In a T it is the other way round: the shunt arm at low attenuation and the input series arm at high attenuation. The calculator names the hottest one.
  • Pads improve match. A pad of AA dB improves the return loss of whatever is behind it by 2A2A dB. A 6 dB pad turns a 10 dB return-loss load into at least 22 dB, at the cost of the 6 dB.
  • 75 Ω to 50 Ω. The minimum-loss pad costs 5.7 dB. If you do not need the full bandwidth of a resistive network, a matching transformer or an L-match is almost lossless.
  • Bridged-T for variable attenuators: the arms stay at Z0Z_0, and only the bridge and shunt values change, with Rbridge⋅Rshunt=Z02R_\text{bridge} \cdot R_\text{shunt} = Z_0^2.

References

  1. Reference Data for Radio Engineers, 6th ed., Howard W. Sams / ITT, 1975, ch. 10 “Attenuators” (symmetrical and asymmetrical T, Pi, bridged-T and minimum-loss pads).
  2. F. E. Terman, Radio Engineers' Handbook, McGraw-Hill, 1943, §3 “Attenuators” (pad design equations and minimum-loss networks).
  3. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, §4.4 (ABCD matrices) and §2.3 (return loss), used for the standard-value check.

This calculator's results are checked against 41 independent reference values in automated tests on every change. How we check accuracy.