Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • LED ResistorSeries resistor for one LED or a string of LEDs: exact value, next standard E12/E24/E96 value, actual current, resistor power and recommended rating.Electronics basics

Voltage Divider Calculator (with Load Resistance)

Output voltage of a two-resistor divider with and without a load, its Thevenin output resistance, and the current and power in every resistor.

Inputs

Whatever the output drives: a meter, an ADC input, the next stage. A 10 MΩ multimeter is a light load.

Results

Output voltage with load(Vout)
5.7143
Output voltage, no load(Vout,nl)
6
Thevenin (output) resistance(Rth)
5
Output drop caused by the load(ΔV/V)
4.7619%
Division ratio Vout / Vin
0.47619
Supply current (through R1)(I1)
628.57
Current through R2(I2)
571.43
Load current(IL)
57.143
Power in R1(P1)
3.951
Power in R2(P2)
3.2653
Power in the load(PL)
326.53
Total power from the supply(Ptot)
7.5429

Formulas

Vout,nl=Vin R2R1+R2,Rth=R1∥R2=R1R2R1+R2V_\mathrm{out,nl} = V_\mathrm{in}\,\frac{R_2}{R_1 + R_2},\qquad R_\mathrm{th} = R_1 \parallel R_2 = \frac{R_1 R_2}{R_1 + R_2}Vout=Vin R2∥RLR1+R2∥RL=Vout,nl RLRL+RthV_\mathrm{out} = V_\mathrm{in}\,\frac{R_2 \parallel R_L}{R_1 + R_2 \parallel R_L} = V_\mathrm{out,nl}\,\frac{R_L}{R_L + R_\mathrm{th}}I1=VinR1+R2∥RL,P1=I12R1,P2=Vout2R2I_1 = \frac{V_\mathrm{in}}{R_1 + R_2 \parallel R_L},\qquad P_1 = I_1^2 R_1,\qquad P_2 = \frac{V_\mathrm{out}^2}{R_2}

What this calculator does

A voltage divider is two resistors in series across a supply. The output is taken from the point between them. The same current flows through both resistors, so the supply voltage is shared between them in proportion to their resistances. With nothing connected to the output, the voltage across the bottom resistor R2R_2 is

Vout,nl=Vin R2R1+R2.V_\mathrm{out,nl} = V_\mathrm{in}\,\frac{R_2}{R_1 + R_2}.

The "nl" stands for no load. Equal resistors give half the supply; R2=3R1R_2 = 3R_1 gives three quarters.

The catch is that a divider is only useful if something is connected to its output, and whatever you connect draws current. That load resistance RLR_L sits in parallel with R2R_2, so the bottom leg of the divider becomes R2∥RLR_2 \parallel R_L, which is always smaller than R2R_2. The loaded output is therefore lower:

Vout=Vin R2∥RLR1+R2∥RL,R2∥RL=R2RLR2+RL.V_\mathrm{out} = V_\mathrm{in}\,\frac{R_2 \parallel R_L}{R_1 + R_2 \parallel R_L}, \qquad R_2 \parallel R_L = \frac{R_2 R_L}{R_2 + R_L}.

The calculator shows both numbers, the percentage the load pulls the output down, the current through each part and the power each one dissipates.

The Thevenin view

There is a neater way to see the loading effect. Thevenin's theorem says that, seen from the output, any network of sources and resistors behaves exactly like one voltage source in series with one resistor. For the divider, the source is the unloaded output Vout,nlV_\mathrm{out,nl} and the resistor is

Rth=R1∥R2=R1R2R1+R2.R_\mathrm{th} = R_1 \parallel R_2 = \frac{R_1 R_2}{R_1 + R_2}.

A load RLR_L and RthR_\mathrm{th} then form a second divider, so

Vout=Vout,nl RLRL+Rth.V_\mathrm{out} = V_\mathrm{out,nl}\,\frac{R_L}{R_L + R_\mathrm{th}}.

This gives the most useful rule of thumb for dividers: the load should be at least 10 times larger than RthR_\mathrm{th}. Then the output falls by less than about 10 %. For 1 % accuracy you need RLR_L about 100 times RthR_\mathrm{th}. The calculator warns you when the load is less than 10 times RthR_\mathrm{th}.

How to use solve-for

Click ⇄ Solve next to a resistor to design a divider. For example, to get 3.3 V from 5 V, set the input to 5 V, keep R1R_1 = 10 kΩ, click ⇄ Solve next to R2R_2, pick Output voltage, no load and type 3.3. The calculator finds R2R_2 ≈ 19.41 kΩ; round it to a standard value (18 kΩ or 20 kΩ) and check the result. You can also solve the load resistance for the output voltage you can accept, which tells you the lightest load the divider can drive.

Worked example

A 12 V supply feeds two 10 kΩ resistors. The output drives a circuit with an input resistance of 100 kΩ. These are the calculator's defaults.

  1. No load: Vout,nl=12×10/(10+10)=6 VV_\mathrm{out,nl} = 12 \times 10/(10 + 10) = 6\ \text{V}.
  2. Output resistance: Rth=10 k∥10 k=5 kΩR_\mathrm{th} = 10\,\text{k} \parallel 10\,\text{k} = 5\ \text{k}\Omega.
  3. With the load: R2∥RL=(10×100)/(10+100)=9.0909 kΩR_2 \parallel R_L = (10 \times 100)/(10 + 100) = 9.0909\ \text{k}\Omega, so Vout=12×9.0909/(10+9.0909)V_\mathrm{out} = 12 \times 9.0909/(10 + 9.0909) = 5.7143 V. The Thevenin form gives the same answer: 6×100/(100+5)=5.71436 \times 100/(100 + 5) = 5.7143 V.
  4. Loading error: 1−5.7143/61 - 5.7143/6 = 4.7619 %. The load is 20 times RthR_\mathrm{th}, so the error is below 10 % but not negligible.
  5. Currents: the supply current is 12/(10 k+9.0909 k)12/(10\,\text{k} + 9.0909\,\text{k}) = 628.57 µA. Of that, 571.43 µA flows through R2R_2 and 57.143 µA through the load.
  6. Power: R1R_1 dissipates 3.951 mW, R2R_2 3.2653 mW and the load 326.53 µW; the supply delivers 7.5429 mW in total.

The division ratio shown is the loaded value, 5.7143/12=0.476195.7143/12 = 0.47619.

Accuracy and validity

The equations are exact for ideal resistors and an ideal (zero-resistance) supply. In practice:

EffectTypical size
Resistor toleranceWith two 1 % resistors the ratio can be off by up to about 1 %; with 5 % parts, up to about 5 %.
Supply resistanceAdds to R1R_1; negligible for a regulated supply, noticeable for a battery feeding a low-value divider.
Load that is not a resistorTransistor bases, op-amp bias currents and ADC sampling inputs draw current in pulses or non-linearly.
TemperatureResistors with the same temperature coefficient track each other, so the ratio drifts much less than either value.

Practical notes

  • A divider is not a power supply. Never use one to power a load whose current changes, such as a motor, a microcontroller or an LED strip. Its output resistance is far too high. Use a voltage regulator.
  • Choosing the resistor size. Low values (hundreds of ohms) make the output stiff but waste power and drain batteries. High values (megohms) waste nothing but are easily loaded and pick up noise. For reading a battery voltage with a microcontroller ADC, 10 kΩ to 100 kΩ is a common range, often with a 100 nF capacitor across R2R_2.
  • Measuring with a meter. A digital multimeter typically has an input resistance of 10 MΩ. On a divider made of 1 MΩ resistors that is a 10× load, and the meter reading will be several percent low.
  • Potentiometers are adjustable dividers: the wiper splits one resistor into R1R_1 and R2R_2.

References

  1. P. Horowitz and W. Hill, The Art of Electronics, 3rd ed., Cambridge University Press, 2015, §1.2.5 (voltage dividers) and §1.2.6 (Thévenin equivalent circuit).
  2. L. Thévenin, “Extension de la loi d'Ohm aux circuits électromoteurs complexes,” Annales Télégraphiques, vol. 10, pp. 222–224, 1883.
  3. W. H. Hayt, J. E. Kemmerly and S. M. Durbin, Engineering Circuit Analysis, 8th ed., McGraw-Hill, 2012, ch. 3 (voltage and current division) and ch. 5 (Thévenin equivalents).