Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • LED ResistorSeries resistor for one LED or a string of LEDs: exact value, next standard E12/E24/E96 value, actual current, resistor power and recommended rating.Electronics basics

Ohm's Law Calculator (Voltage, Current, Resistance, Power)

Enter any two of voltage, current, resistance and power to get the other two, using Ohm's law V = IR and the power law P = VI.

Inputs

Results

Voltage(V)
12
Current(I)
12
Resistance(R)
1
Power(P)
144
Conductance (1/R)(G)
1
  • A resistor dissipating 0.144 W should be rated for at least 0.29 W (twice the power).

Formulas

V=IR,I=VR,R=VIV = I R,\qquad I = \frac{V}{R},\qquad R = \frac{V}{I}P=VI=I2R=V2RP = V I = I^2 R = \frac{V^2}{R}V=PR,I=PR,G=1RV = \sqrt{P R},\qquad I = \sqrt{\frac{P}{R}},\qquad G = \frac{1}{R}

What this calculator does

Ohm's law links the three basic quantities of a circuit:

  • Voltage VV, in volts (V), is the electrical "push" between two points.
  • Current II, in amperes (A), is how much charge flows past a point each second.
  • Resistance RR, in ohms (Ω), is how strongly a component opposes that flow.

For a resistor they are tied together by

V=IR.V = I R .

Double the voltage across a resistor and the current doubles. Double the resistance at the same voltage and the current halves. A fourth quantity, power PP in watts (W), is the rate at which the resistor turns electrical energy into heat:

P=VI.P = V I .

Put the two equations together and you get two more forms, P=I2RP = I^2 R and P=V2/RP = V^2/R. With these four relations, any two of V, I, R and P fix the other two. Choose the pair you know in the I know menu, type the two values, and the calculator fills in the rest. It also shows the conductance G=1/RG = 1/R in siemens (S), which is handy when you work with parallel circuits.

Which formula is used

You knowVoltageCurrentResistancePower
V and IgivengivenV/IV/IVIVI
V and RgivenV/RV/RgivenV2/RV^2/R
I and RIRIRgivengivenI2RI^2R
P and VgivenP/VP/VV2/PV^2/Pgiven
P and IP/IP/IgivenP/I2P/I^2given
P and RPR\sqrt{PR}P/R\sqrt{P/R}givengiven

Working backwards

There is no separate solve-for button here, because the I know menu already covers every case. To find the voltage that makes a 1 kΩ resistor dissipate 1 W, choose power and resistance and enter 1 W and 1 kΩ: the calculator gives V=PRV = \sqrt{PR} = 31.623 V.

Worked example

A 1 kΩ resistor is connected across a 12 V supply. How much current flows, and how hot does the resistor get?

  1. Current: I=V/R=12 V/1000 Ω=0.012 AI = V/R = 12\ \text{V} / 1000\ \Omega = 0.012\ \text{A}, which is 12 mA.
  2. Power: P=V2/R=144/1000=0.144 WP = V^2/R = 144 / 1000 = 0.144\ \text{W}, which is 144 mW.
  3. Conductance: G=1/RG = 1/R = 1 mS.

These are the calculator's defaults, so the results panel shows 12 V, 12 mA, 1 kΩ, 144 mW and 1 mS. A common 1/4 W (250 mW) resistor would survive, but it would run warm. The usual rule is to choose a power rating at least twice the power the resistor dissipates, here at least 0.29 W, so the calculator suggests that. A 1/2 W resistor is the safe choice.

A second example: a loudspeaker is modelled as an 8 Ω resistor and you want to deliver 10 W. Choose Power and resistance, enter 10 W and 8 Ω. The voltage is PR=80\sqrt{PR} = \sqrt{80} = 8.9443 V and the current is P/R=1.25\sqrt{P/R} = \sqrt{1.25} = 1.118 A.

Accuracy and validity

The equations are exact for an ideal resistor: a component whose resistance does not depend on the voltage across it or the current through it. The calculator's arithmetic is exact to the digits shown. The limits come from the real world:

EffectWhen it matters
Resistor toleranceAlways: a 5 % resistor marked 1 kΩ can be anything from 950 Ω to 1050 Ω.
TemperatureResistance changes as the part heats up; for metals, by about +0.4 % per °C.
Non-linear partsDiodes, LEDs, lamps and transistors do not obey V=IRV = IR with a fixed RR.
AC circuitsWith capacitors and inductors, use impedance and RMS values instead.

Ohm's law still holds at any instant for a resistor in an AC circuit. With RMS voltage and current, P=VIP = VI gives the average power.

A filament lamp is a good warning example. Its resistance when hot can be ten times its resistance when cold, so "the resistance of a lamp" depends on how you measure it.

Practical notes

  • Units and prefixes. Most mistakes are factor-of-1000 errors. 5 V across 2.2 kΩ is 2.27 mA, not 2.27 A. Type the prefix with the number (for example 2.2k or 20 mA) and the calculator converts it.
  • Power rating. Choose a resistor rated for at least twice the power it dissipates. Small through-hole resistors are commonly 1/4 W; small surface-mount ones (0603, 0402) are often only 1/10 W or less.
  • Safety. Voltages above about 50 V can drive a dangerous current through the body. Mains circuits must be handled by people trained for it.
  • Measuring. Measure current with the meter in series with the circuit, and voltage with the meter across the component. Measuring resistance only works with the power off.

References

  1. G. S. Ohm, Die galvanische Kette, mathematisch bearbeitet, T. H. Riemann, Berlin, 1827.
  2. P. Horowitz and W. Hill, The Art of Electronics, 3rd ed., Cambridge University Press, 2015, §1.2 (voltage, current, resistance and power).
  3. W. H. Hayt, J. E. Kemmerly and S. M. Durbin, Engineering Circuit Analysis, 8th ed., McGraw-Hill, 2012, ch. 2 (Ohm's law and the power absorbed by a resistor).