Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • LED ResistorSeries resistor for one LED or a string of LEDs: exact value, next standard E12/E24/E96 value, actual current, resistor power and recommended rating.Electronics basics

Series and Parallel Resistor, Inductor and Capacitor Calculator

Total resistance, inductance or capacitance of up to six components in series and in parallel. Solve for the part that gives a target total.

Inputs

Results

Series total(Rs)
14.7
Parallel total(Rp)
3.1973

Formulas

Rs=R1+R2+⋯+Rn,1Rp=1R1+1R2+⋯+1RnR_s = R_1 + R_2 + \dots + R_n,\qquad \frac{1}{R_p} = \frac{1}{R_1} + \frac{1}{R_2} + \dots + \frac{1}{R_n}Ls=L1+L2+⋯+Ln,1Lp=1L1+1L2+⋯+1LnL_s = L_1 + L_2 + \dots + L_n,\qquad \frac{1}{L_p} = \frac{1}{L_1} + \frac{1}{L_2} + \dots + \frac{1}{L_n}1Cs=1C1+1C2+⋯+1Cn,Cp=C1+C2+⋯+Cn\frac{1}{C_s} = \frac{1}{C_1} + \frac{1}{C_2} + \dots + \frac{1}{C_n},\qquad C_p = C_1 + C_2 + \dots + C_ntwo parts: R1∥R2=R1R2R1+R2\text{two parts: } R_1 \parallel R_2 = \frac{R_1 R_2}{R_1 + R_2}

What this calculator does

Components are connected in two basic ways:

  • In series, they are joined end to end, so the same current flows through every one of them.
  • In parallel, they are connected across the same two points, so they all have the same voltage.

Choose the component type and how many parts you have (2 to 6), type their values, and the calculator shows the single component that would behave the same in series and in parallel.

Resistors

In series, each resistor adds its own voltage drop for the same current, so the resistances simply add:

Rs=R1+R2+⋯+Rn.R_s = R_1 + R_2 + \dots + R_n .

In parallel, each resistor adds its own current path at the same voltage, so the conductances 1/R1/R add:

1Rp=1R1+1R2+⋯+1Rn.\frac{1}{R_p} = \frac{1}{R_1} + \frac{1}{R_2} + \dots + \frac{1}{R_n}.

For two resistors this becomes the "product over sum" rule, Rp=R1R2/(R1+R2)R_p = R_1R_2/(R_1+R_2). Two useful checks: the parallel total is always smaller than the smallest resistor, and nn equal resistors in parallel give R/nR/n.

Inductors

Inductors combine the same way as resistors, as long as their magnetic fields do not interact:

Ls=L1+L2+…,1Lp=1L1+1L2+…L_s = L_1 + L_2 + \dots,\qquad \frac{1}{L_p} = \frac{1}{L_1} + \frac{1}{L_2} + \dots

If two coils are close together and share magnetic flux (mutual inductance MM), the series total becomes L1+L2±2ML_1 + L_2 \pm 2M depending on how they are wound. This calculator assumes M=0M = 0.

Capacitors work the other way round

A capacitor stores charge on its plates, and capacitance is charge per volt, C=Q/VC = Q/V. Connected in parallel, the capacitors all see the same voltage and their charges add, so the capacitances add:

Cp=C1+C2+…C_p = C_1 + C_2 + \dots

Connected in series, they all carry the same charge and their voltages add, so it is the reciprocals that add:

1Cs=1C1+1C2+…\frac{1}{C_s} = \frac{1}{C_1} + \frac{1}{C_2} + \dots

So capacitors in series combine like resistors in parallel, and capacitors in parallel combine like resistors in series. The series total is always smaller than the smallest capacitor.

How to use solve-for

A common question is "what resistor do I put in parallel with this one to get the value I need?". Keep R1R_1 = 10 kΩ, click ⇄ Solve next to resistor 2, choose Parallel total and type 4.7k. The calculator finds R2R_2 ≈ 8.868 kΩ. The same works for inductor 2 and capacitor 2, for example to find which capacitor in series with a 100 nF part gives 68 nF.

Worked example

Two resistors, 10 kΩ and 4.7 kΩ (the defaults):

  • Series: 10+4.710 + 4.7 = 14.7 kΩ.
  • Parallel: (10×4.7)/(10+4.7)=47/14.7(10 \times 4.7)/(10 + 4.7) = 47/14.7 = 3.1973 kΩ. As expected, it is below 4.7 kΩ.

Now switch to Capacitors, choose 3 components and enter 100 nF, 220 nF and 470 nF:

  • Parallel: 100+220+470100 + 220 + 470 = 790 nF.
  • Series: 1/(1/100+1/220+1/470)1/(1/100 + 1/220 + 1/470) nF = 59.977 nF, a little below the smallest capacitor.

Accuracy and validity

The formulas are exact for ideal components. Real parts add a few complications:

EffectWhen it matters
ToleranceTotals inherit the tolerance of the parts: 5 % resistors give a total within about 5 %.
Capacitors in series share voltage unevenlyAt DC the voltage divides according to leakage, not capacitance. Add equal "balancing" resistors across each capacitor when stacking them for high voltage.
Mutual inductanceCoupled inductors do not follow the simple rules.
High frequencyLead inductance and stray capacitance matter above roughly 10–100 MHz.

Practical notes

  • Making odd values. Two standard resistors in parallel or series can make almost any value. Putting two equal resistors in parallel also doubles the power rating of the pair.
  • Capacitors in parallel are often used on purpose: a large electrolytic for bulk storage plus a small 100 nF ceramic for high-frequency decoupling.
  • Quick estimate. If one parallel resistor is ten times the other, the total is about 9 % below the smaller one. If it is 100 times, about 1 % below.

References

  1. P. Horowitz and W. Hill, The Art of Electronics, 3rd ed., Cambridge University Press, 2015, §1.2.1 (resistors in series and parallel) and §1.4 (capacitors and inductors).
  2. W. H. Hayt, J. E. Kemmerly and S. M. Durbin, Engineering Circuit Analysis, 8th ed., McGraw-Hill, 2012, §3.6 (series and parallel resistors) and §7.4 (inductance and capacitance combinations).