Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

RF Cascade Analysis Calculator (Noise Figure, IP3, P1dB, SFDR)

Cascaded gain, Friis noise figure, IIP3/OIP3, P1dB, noise floor, SFDR and sensitivity for a 1–20 stage RF line-up, with a level diagram and share links.

5 cited sources117 reference checksRuns in your browser

Stages (5 of 20)

Signal flows top to bottom. Blank IP3 / OP1dB = ideal (linear).

Cascade stages in signal order. Gain in dB (negative for loss), noise figure in dB, IP3 and output P1dB in dBm.
#NameTypeGain (dB)NF (dB)IP3 (dBm)OP1dB (dBm)Actions
10.50
2
32.00
4
5
Add:

System

dBm
dB
K

290 K = T₀ gives the standard −174 dBm/Hz floor; use the antenna temperature for a receiver.

dB

Flag stages whose output is within this margin of their OP1dB.

IP3 / P1dB summation

Coherent adds IM3 voltages in phase: the worst case, and the usual specification basis. RSS (incoherent) is optimistic.

Results

Gain
28.50dB
Noise figure
2.41dB
Te = 215.5 K
Input IP3 (coherent)
3.16dBm
OIP3 31.66 dBm
Input P1dB (est.)
−9.49dBm
OP1dB 18.01 dBm
Noise floor (input)
−111.56dBm
output −83.06 dBm
SFDR
76.48dB
⅔ (IIP3 − noise floor)
Sensitivity (MDS)
−101.56dBm
noise floor + required SNR
Output signal
−21.50dBm
SNR 61.56 dB
  • NF is referred to T₀ = 290 K; passive stages use NF = loss. P1dB is an estimate from the same summation as IP3, with OP1dB = IP1dB + G − 1 dB.

Per-stage cumulative values

Values at the output of each stage, cumulative from the cascade input. Powers in dBm, gains and noise figures in dB, contributions in percent.
StageGainNFIIP3OIP3IP1dBOP1dBNF shareIP3 shareSignal outNoise outHeadroom
dBdBdBmdBmdBmdBm%%dBmdBmdB
1. Antenna cable−0.500.50∞∞∞∞16.40.0−50.50−113.98∞
2. LNA17.501.7014.5032.003.5020.0048.07.3−32.50−94.7852.50
3. Band-pass filter15.501.7314.5030.003.5018.001.40.0−34.50−96.74∞
4. Mixer8.502.055.8614.36−5.142.3615.246.3−41.50−103.4344.50
5. IF amplifier28.502.413.1631.66−9.4918.0118.946.3−21.50−83.0641.50

Per-stage contributions

  • Noise (share of F − 1)
  • IIP3 degradation (share of 1/IIP3)
0%25%50%75%100%Antenna cable1. Antenna cableStage 1 Antenna cable: 16.4 % of excess noise16.4Stage 1 Antenna cable: 0.0 % of IIP3 degradation0LNA2. LNAStage 2 LNA: 48.0 % of excess noise48.0Stage 2 LNA: 7.3 % of IIP3 degradation7.3Band-pass filter3. Band-pass filterStage 3 Band-pass filter: 1.4 % of excess noise1.4Stage 3 Band-pass filter: 0.0 % of IIP3 degradation0Mixer4. MixerStage 4 Mixer: 15.2 % of excess noise15.2Stage 4 Mixer: 46.3 % of IIP3 degradation46.3IF amplifier5. IF amplifierStage 5 IF amplifier: 18.9 % of excess noise18.9Stage 5 IF amplifier: 46.3 % of IIP3 degradation46.3

Level diagram

  • Signal
  • Noise in bandwidth
  • Stage OP1dB (ideal stages omitted)
−150−100−50050dBmIn12345Stage outputSignalNoiseOP1dB

Formulas

F=F1+F2−1G1+F3−1G1G2+⋯ ,Te=(F−1) T0F = F_1 + \frac{F_2 - 1}{G_1} + \frac{F_3 - 1}{G_1 G_2} + \cdots,\qquad T_e = (F-1)\,T_01IIP3=∑iG1⋯Gi−1IIP3i (coherent),1IIP32=∑i(G1⋯Gi−1IIP3i)2 (RSS)\frac{1}{\mathrm{IIP3}} = \sum_{i} \frac{G_1 \cdots G_{i-1}}{\mathrm{IIP3}_i}\ \text{(coherent)},\qquad \frac{1}{\mathrm{IIP3}^2} = \sum_{i} \left(\frac{G_1 \cdots G_{i-1}}{\mathrm{IIP3}_i}\right)^{2}\ \text{(RSS)}OIP3=IIP3+G,IP1dBi=OP1dBi−(Gi−1 dB),OP1dB=IP1dB+G−1 dB\mathrm{OIP3} = \mathrm{IIP3} + G,\qquad \mathrm{IP1dB}_i = \mathrm{OP1dB}_i - (G_i - 1\,\mathrm{dB}),\qquad \mathrm{OP1dB} = \mathrm{IP1dB} + G - 1\,\mathrm{dB}Nin=k (Ts+Te) B  →Ts=T0  −174 dBm/Hz+10log⁡10B+NFN_{\mathrm{in}} = k\,(T_s + T_e)\,B \;\xrightarrow{T_s = T_0}\; -174\,\mathrm{dBm/Hz} + 10\log_{10} B + \mathrm{NF}SFDR=23(IIP3−Nin),MDS=Nin+SNRreq\mathrm{SFDR} = \tfrac{2}{3}\left(\mathrm{IIP3} - N_{\mathrm{in}}\right),\qquad \mathrm{MDS} = N_{\mathrm{in}} + \mathrm{SNR}_{\mathrm{req}}

What this calculator does

A receiver or transmitter line-up is a chain of two-ports: cables, filters, amplifiers, mixers and attenuators. Each stage has a gain, a noise figure, a third-order intercept and a compression point. The cascade analysis turns those per-stage numbers into the system figures you actually specify: total gain, noise figure, input and output IP3, P1dB, noise floor, spurious-free dynamic range (SFDR) and sensitivity. It also shows the signal and noise level at every stage output, so you can see where the line-up runs out of headroom.

The table above takes 1 to 20 stages. All the arithmetic is done in linear units (mW and power ratios), and the results are converted back to dB and dBm only for display. Stages are evaluated in the order listed, from the antenna (or signal source) towards the output.

Gain and noise figure (Friis)

The cascade gain is the sum of the stage gains in dB. The noise factor F=10NF/10F = 10^{\mathrm{NF}/10} follows Friis's formula, in which each stage's excess noise is divided by the gain ahead of it:

F=F1+F2−1G1+F3−1G1G2+⋯ ,Te=(F−1) T0F = F_1 + \frac{F_2 - 1}{G_1} + \frac{F_3 - 1}{G_1 G_2} + \cdots, \qquad T_e = (F - 1)\,T_0

Here T0=290 KT_0 = 290\ \mathrm{K} is the reference temperature that defines noise figure. The NF share column shows each term (Fi−1)/(G1⋯Gi−1)(F_i - 1)/(G_1 \cdots G_{i-1}) as a percentage of the total F−1F - 1. This percentage is also the stage's share of the cascade noise temperature, so it tells you which stage to improve first.

Passive stages. A matched lossy stage (cable, filter, attenuator) at physical temperature T0T_0 has a noise figure equal to its loss, so Te=(L−1)T0T_e = (L - 1)T_0. When you choose Filter / attenuator or Cable, the NF column is locked to the loss and you enter the loss as a negative gain. One consequence is that a loss of LL dB in front of the cascade adds exactly LL dB to the system NF. The test suite checks this property.

Intercept points: coherent vs. RSS

Each stage's IP3 can be entered as an input (IIP3) or output (OIP3) value; the two are related by OIP3=IIP3+G\mathrm{OIP3} = \mathrm{IIP3} + G. Referred to the cascade input, the intercepts combine as follows.

Coherent (default, worst case). The third-order products of all stages are assumed to add in phase as voltages:

1IIP3=1IIP31+G1IIP32+G1G2IIP33+⋯\frac{1}{\mathrm{IIP3}} = \frac{1}{\mathrm{IIP3}_1} + \frac{G_1}{\mathrm{IIP3}_2} + \frac{G_1 G_2}{\mathrm{IIP3}_3} + \cdots

This is the formula in Pozar, Egan and Razavi, and it is the basis most specifications are written against. It never overestimates the intercept of a cascade of memoryless stages.

RSS (incoherent). If the IM3 products of different stages have unrelated phases, their powers add instead of their voltages:

1IIP32=∑i(G1⋯Gi−1IIP3i)2\frac{1}{\mathrm{IIP3}^2} = \sum_i \left(\frac{G_1 \cdots G_{i-1}}{\mathrm{IIP3}_i}\right)^{2}

RSS always gives a higher IIP3 than coherent summation. When two stages contribute equally, the difference is 10log⁡10(2)/2≈1.510\log_{10}(2)/2 \approx 1.5 dB. When one stage dominates, the two methods converge. Use RSS as an optimistic bound or a "typical" estimate. Filters with phase shift between stages, or wideband signals, usually measure somewhere between the two. The IP3 share column gives each stage's term as a percentage of the sum (or of the sum of squares in RSS mode). A stage with a high share is the one limiting linearity.

Compression (P1dB)

The cascaded P1dB uses the same summation on input-referred compression points. A stage's input P1dB is IP1dBi=OP1dBi−(Gi−1 dB)\mathrm{IP1dB}_i = \mathrm{OP1dB}_i - (G_i - 1\ \mathrm{dB}), because at the 1 dB point the gain has dropped by 1 dB. The cascade output value is OP1dB=IP1dB+G−1 dB\mathrm{OP1dB} = \mathrm{IP1dB} + G - 1\ \mathrm{dB}. Some spreadsheets omit the 1 dB, which makes their input P1dB 1 dB lower than the value shown here.

This is an approximation. Compression is a large-signal effect, and the real cascade 1 dB point depends on the full AM/AM curve of every stage. In practice the last active stage usually dominates, and the estimate is good to about a dB when one stage clearly sets the limit. Treat it as a planning number and confirm it by measurement or harmonic-balance simulation.

The level diagram and the Headroom column compare each stage's small-signal output level with its own OP1dB. Stages within the compression warning margin (6 dB by default) are flagged.

Noise floor, SFDR and sensitivity

The noise floor is referred to the cascade input:

Nin=k (Ts+Te) BN_{\mathrm{in}} = k\,(T_s + T_e)\,B

With the source at Ts=T0T_s = T_0, this reduces to the familiar −174 dBm/Hz+10log⁡10B+NF-174\ \mathrm{dBm/Hz} + 10\log_{10}B + \mathrm{NF} (more precisely −173.975-173.975 dBm/Hz). For an antenna looking at cold sky, set TsT_s to the antenna temperature. The noise figure itself is always referred to 290 K.

From the floor and the input intercept, the calculator gives:

  • SFDR =23(IIP3−Nin)= \tfrac{2}{3}(\mathrm{IIP3} - N_{\mathrm{in}}). This is the range of input levels over which two equal tones produce third-order products no larger than the noise floor.
  • Sensitivity (MDS) =Nin+SNRreq= N_{\mathrm{in}} + \mathrm{SNR}_{\mathrm{req}}. This is the weakest signal that reaches the required SNR in the noise bandwidth BB.

Use the noise bandwidth of the final channel filter, not its 3 dB bandwidth, if you know it.

Worked example

The default line-up is a superheterodyne front end with a 1 MHz noise bandwidth, an input signal of −50 dBm and a source at 290 K:

#StageGainNFIP3OP1dB
1Antenna cable−0.5 dB0.5 dB (= loss)idealideal
2LNA18 dB1.2 dBOIP3 +32 dBm+20 dBm
3Band-pass filter−2 dB2 dB (= loss)idealideal
4Mixer−7 dB7 dBOIP3 +15 dBm+3 dBm
5IF amplifier20 dB3 dBOIP3 +35 dBm+20 dBm

Noise. The gains ahead of the five stages are 1, 0.891, 56.23, 35.48 and 7.079. The Friis terms (Fi−1)/Gbefore(F_i - 1)/G_{\text{before}} are 0.1220, 0.3571, 0.0104, 0.1131 and 0.1406, which sum to F−1=0.7432F - 1 = 0.7432. So F=1.7432F = 1.7432, giving NF = 2.41 dB and Te=215.5T_e = 215.5 K. The LNA contributes 48.0 % of the excess noise. The 0.5 dB cable in front of it contributes 16.4 %, because nothing amplifies the signal before the cable.

Linearity. The stage input intercepts are +14 dBm (LNA), +22 dBm (mixer) and +15 dBm (IF amplifier). Referred to the antenna, the coherent terms Gbefore/IIP3iG_{\text{before}}/\mathrm{IIP3}_i are 0.0355, 0.2239 and 0.2239 mW⁻¹. Their sum is 0.4832 mW⁻¹, so IIP3 = +3.16 dBm and OIP3 = +31.66 dBm. The mixer and the IF amplifier each account for 46.3 %: with this much gain in front of them, they limit linearity, not the LNA. With the RSS toggle, IIP3 rises to +4.97 dBm.

Compression. The estimated input P1dB is −9.49 dBm and the output P1dB is +18.01 dBm.

Floor and dynamic range. Nin=−173.975+60+2.413=N_{\mathrm{in}} = -173.975 + 60 + 2.413 = −111.56 dBm. With a 10 dB SNR requirement, the sensitivity is −101.56 dBm. SFDR =23(3.16+111.56)== \tfrac{2}{3}(3.16 + 111.56) = 76.48 dB. The −50 dBm input leaves the cascade at −21.5 dBm, more than 40 dB below the IF amplifier's +20 dBm OP1dB.

Accuracy and validity

QuantityModelError sources
Gain, NFExact for matched stages (available gain)Mismatch between stages; NF quoted at a different source impedance
IIP3 / OIP3Coherent: exact worst case for memoryless 3rd-order stagesFrequency-dependent phase (filters), higher-order terms
P1dBEstimate from intercept-style summationTypically ±1 dB when one stage dominates
Noise floor, MDSk(Ts+Te)Bk(T_s + T_e)BNoise bandwidth vs. 3 dB bandwidth; image noise in mixers

The tests check the results against an independent Python implementation of the textbook formulas, written separately from the TypeScript (it works with noise temperatures and output-referred intercepts), on 24 random cascades of 1 to 10 stages. They also check exact limits: a single stage is unchanged, an ideal 0 dB stage changes nothing, and a pad in front adds its loss to NF and IIP3.

Practical notes

  • Use available gain. Datasheet ∣S21∣2|S_{21}|^2 differs from available gain when stages are mismatched. For a well-matched 50 Ω chain the difference is small; across a filter skirt it is not.
  • Mixer NF. Use the SSB noise figure for a single-sideband receiver. A DSB figure is about 3 dB optimistic for an image-rejected design.
  • Put the loss after the gain. Every dB of loss in front of the LNA appears directly in the NF. Behind 20 dB of gain, the same loss costs a few hundredths of a dB.
  • Gain is not free. Extra gain ahead of the mixer lowers NF but raises the IM3 share of every later stage. The contribution chart shows that trade-off.
  • Cross-check. The CSV export gives every per-stage value to 0.001 dB for comparison with a spreadsheet.

Sources for the formulas

Friis (1944) for the noise cascade; Pozar, Microwave Engineering (4th ed., ch. 10) for passive-stage noise, intercept points and dynamic range; Egan, Practical RF System Design, for coherent and RSS intermodulation and compression in line-ups; Razavi, RF Microelectronics (2nd ed., ch. 2) for cascaded nonlinearity. The full citations are listed below.

References

  1. H. T. Friis, "Noise figures of radio receivers," Proc. IRE, vol. 32, no. 7, pp. 419–422, July 1944.
  2. D. M. Pozar, Microwave Engineering, 4th ed. Hoboken, NJ: Wiley, 2012, ch. 10 (Noise and Nonlinear Distortion).
  3. W. F. Egan, Practical RF System Design. Hoboken, NJ: Wiley-IEEE Press, 2003 (cascaded gain, noise figure, intermodulation and compression).
  4. B. Razavi, RF Microelectronics, 2nd ed. Upper Saddle River, NJ: Prentice Hall, 2011, ch. 2 (nonlinearity of cascaded stages).
  5. IRE Subcommittee 7.9 on Noise, "IRE standards on methods of measuring noise in linear twoports, 1959," Proc. IRE, vol. 48, no. 1, pp. 60–68, Jan. 1960 (reference temperature T0 = 290 K).

This calculator's results are checked against 117 independent reference values in automated tests on every change. How we check accuracy.