Skip to content
FiftyOhm
Esc
  • Air-core coilSingle-layer air-core solenoid inductance from Nagaoka's exact coefficient, compared with Wheeler's formula. Solve for the number of turns for a target inductance.Components & magnetics
  • Attenuator PadsResistor values for Pi, T, bridged-T and minimum-loss L-pad attenuators, with unequal impedances, power dissipation per resistor and E24/E96 rounding.Couplers, dividers & attenuators
  • CoaxCoax Z0, capacitance and inductance per length, velocity factor, loss, exact TE11 cutoff and breakdown voltage. Solve for D, d or εr from Z0.Transmission lines
  • CPW / GCPWCoplanar waveguide and grounded CPW impedance, effective permittivity, dispersion, delay and loss by conformal mapping. Solve for centre width or gap.Transmission lines
  • dBm ↔ W ↔ VConvert RF power between dBm, dBW, watts, Vrms, Vpeak, Vpp, dBµV and dBmV for any system impedance. Instant, accurate, with formulas.Fundamentals & conversions
  • Differential pairEdge-coupled microstrip and stripline differential impedance, Z0 even/odd, common-mode impedance, coupling and delay. Solve for spacing or width from Zdiff.Transmission lines
  • Filter OrderMinimum filter order to meet a passband/stopband attenuation mask for Butterworth, Chebyshev and elliptic responses, with the attenuation actually achieved.Filters
  • Free-space path lossFree-space path loss from the Friis equation, received power with antenna gains, and a far-field check. Solve for distance or frequency.Propagation & link budget
  • L / Pi / T MatchingDesign lumped L, Pi and T matching networks between complex source and load impedances. Both L solutions, loaded-Q Pi/T, component values and bandwidth.Matching & Smith chart
  • LC Filter DesignerDesign lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.Filters
  • MicrostripMicrostrip Z0, effective permittivity, dispersion, delay and loss. Solve for trace width from target impedance. Hammerstad–Jensen + Kirschning–Jansen models.Transmission lines

LC Filter Designer (Butterworth, Chebyshev, Bessel)

Design lumped LC ladder filters: Butterworth, Chebyshev or Bessel; low-pass, high-pass, band-pass, band-stop to order 10, with exact insertion loss and group delay.

5 cited sources401 reference checksRuns in your browser

Inputs

Number of reactive elements (resonators for band-pass and band-stop).

Butterworth and Bessel: 3 dB frequency. Chebyshev: edge of the ripple band (attenuation = ripple).

Frequency at which insertion loss, return loss and group delay are evaluated. Sweep it to plot the response.

Results

Insertion loss at f(IL)
3.0103dB
Group delay at f(τ_g)
791.34
Return loss at f(RL)
3.0103dB
Load resistance(R_L)
50
Prototype g(N+1) (load)(g_{N+1})
1
Element 1 (shunt C)(C1)
1.9673
Element 2 (series L)(L2)
12.876
Element 3 (shunt C)(C3)
6.3662
Element 4 (series L)(L4)
12.876
Element 5 (shunt C)(C5)
1.9673
Prototype g1(g1)
0.61803
Prototype g2(g2)
1.618
Prototype g3(g3)
2
Prototype g4(g4)
1.618
Prototype g5(g5)
0.61803
  • Above a few hundred MHz, lumped parts are limited by self-resonance, pad parasitics and finite Q. Keep each part's SRF well above the highest frequency of interest (≥ 2–3×), or use a distributed (stepped-impedance, coupled-line) realization.

Formulas

Butterworth: gk=2sin⁡(2k−1)π2N,gN+1=1,IL=10log⁡10 ⁣(1+Ω2N)\text{Butterworth: } g_k = 2\sin\frac{(2k-1)\pi}{2N},\quad g_{N+1}=1,\quad \mathrm{IL} = 10\log_{10}\!\left(1+\Omega^{2N}\right)Chebyshev: β=ln⁡coth⁡LAr17.37, γ=sinh⁡β2N, g1=2a1γ, gk=4ak−1akbk−1gk−1\text{Chebyshev: } \beta=\ln\coth\frac{L_{Ar}}{17.37},\ \gamma=\sinh\frac{\beta}{2N},\ g_1=\frac{2a_1}{\gamma},\ g_k=\frac{4a_{k-1}a_k}{b_{k-1}g_{k-1}}ak=sin⁡(2k−1)π2N, bk=γ2+sin⁡2kπN, gN+1={1N oddcoth⁡2(β/4)N evena_k=\sin\frac{(2k-1)\pi}{2N},\ b_k=\gamma^2+\sin^2\frac{k\pi}{N},\ g_{N+1}=\begin{cases}1 & N\ \text{odd}\\ \coth^2(\beta/4) & N\ \text{even}\end{cases}Bessel: gk(3 dB)=ω3dB gk(τ=1)\text{Bessel: } g_k^{(3\,\mathrm{dB})} = \omega_{3\mathrm{dB}}\,g_k^{(\tau=1)}LP: Lk=R0gkωc, Ck=gkR0ωcHP: Lk=R0ωcgk, Ck=1R0ωcgk\text{LP: } L_k=\frac{R_0 g_k}{\omega_c},\ C_k=\frac{g_k}{R_0\omega_c}\qquad \text{HP: } L_k=\frac{R_0}{\omega_c g_k},\ C_k=\frac{1}{R_0\omega_c g_k}BP: series L=R0gkω0Δ, C=Δω0R0gk; shunt L=R0Δω0gk, C=gkω0ΔR0\text{BP: series } L=\frac{R_0 g_k}{\omega_0\Delta},\ C=\frac{\Delta}{\omega_0 R_0 g_k};\ \text{shunt } L=\frac{R_0\Delta}{\omega_0 g_k},\ C=\frac{g_k}{\omega_0\Delta R_0}BS: series L=R0gkΔω0, C=1ω0R0gkΔ; shunt L=R0ω0gkΔ, C=gkΔω0R0\text{BS: series } L=\frac{R_0 g_k\Delta}{\omega_0},\ C=\frac{1}{\omega_0 R_0 g_k\Delta};\ \text{shunt } L=\frac{R_0}{\omega_0 g_k\Delta},\ C=\frac{g_k\Delta}{\omega_0 R_0}ω0=ω1ω2,Δ=ω2−ω1ω0\omega_0=\sqrt{\omega_1\omega_2},\quad \Delta=\frac{\omega_2-\omega_1}{\omega_0}S21=2RSRLARL+B+CRSRL+DRS,τg=−d∠S21dωS_{21}=\frac{2\sqrt{R_S R_L}}{A R_L + B + C R_S R_L + D R_S},\quad \tau_g = -\frac{d\angle S_{21}}{d\omega}

What this calculator does

A lumped LC ladder filter alternates series and shunt reactances between a source and a load resistance. This calculator works in three steps:

  1. It picks a normalized low-pass prototype: a list of element values g1…gNg_1 \dots g_N for a 1 Ω source and a cutoff of 1 rad/s, plus the load value gN+1g_{N+1}.
  2. It scales and transforms the prototype to your system impedance Z0Z_0 and your cutoff (low-pass, high-pass) or band (band-pass, band-stop), using the transformations in Pozar §8.4.
  3. It analyses the real ladder it just built, using ABCD matrices in complex arithmetic. The insertion loss, return loss and group delay at the evaluation frequency ff come from this exact circuit analysis, not from an ideal formula. Sweep ff in the plot panel to see the true response.

The three responses

ResponsePrototypeCutoff fcf_c meansStrength
Butterworthgk=2sin⁡(2k−1)π2Ng_k = 2\sin\frac{(2k-1)\pi}{2N}3 dB pointFlattest passband magnitude
ChebyshevMatthaei/Young/Jones recursionEdge of the ripple band (loss = ripple)Steepest skirt for a given NN among all-pole filters
BesselPublished tables (Zverev; Williams & Taylor)3 dB pointFlattest group delay, little overshoot

Bessel normalization. Bessel tables come in two forms. Delay-normalized tables give a DC group delay of exactly 1 s, and their 3 dB frequency then varies with order (ω3dB=1.3617\omega_{3\text{dB}} = 1.3617 for N=2N = 2, 2.4274 for N=5N = 5, 3.5910 for N=10N = 10). 3 dB-normalized tables put the 3 dB point at 1 rad/s. The two differ only by a frequency scale: gk(3 dB)=ω3dB gk(τ=1)g_k^{(3\,\text{dB})} = \omega_{3\text{dB}}\,g_k^{(\tau=1)}. This calculator always treats fcf_c as the 3 dB frequency. So with ωc=2πfc\omega_c = 2\pi f_c, the DC group delay of a Bessel low-pass is ω3dB(N)/ωc\omega_{3\text{dB}}(N)/\omega_c. The prototype values were synthesized from the Bessel polynomial at 60-digit precision, and they match the published tables to every printed digit.

Even-order Chebyshev. For even NN, gN+1=coth⁡2(β/4)≠1g_{N+1} = \coth^2(\beta/4) \ne 1, so the filter must be terminated in a load different from Z0Z_0 (for 0.5 dB ripple, gN+1=1.9841g_{N+1} = 1.9841). The calculator reports the required load resistance RLR_L, uses it in the analysis and shows a warning. If both ends must be Z0Z_0, use an odd order.

Building the circuit

Element kk sits at position kk counting from the source. With shunt first (Pi), the odd positions are shunt branches to ground. With series first (T), the odd positions are in the signal path. For a low-pass filter, shunt-first gives the minimum-inductor form, which is usually cheaper and has lower loss.

TypeShunt positionSeries position
Low-passC to groundL in line
High-passL to groundC in line
Band-passL ∥ C to groundL and C in series, in line
Band-stopL and C in series, to groundL ∥ C, in line

For band-pass and band-stop filters, f0=f1f2f_0 = \sqrt{f_1 f_2} is the geometric centre, and the bandwidth is f2−f1f_2 - f_1. The calculator reports the two band edges. Because of the geometric mapping, the response is symmetric in log frequency: the loss at f0⋅rf_0 \cdot r equals the loss at f0/rf_0 / r.

How to use solve-for

  • Evaluation frequency from insertion loss: enter 40 dB as the target to find the frequency where the stopband reaches 40 dB. For a band-pass filter there are two solutions; the solver returns the one nearest the current ff.
  • Cutoff frequency from insertion loss: for a fixed order, find the low-pass or high-pass cutoff that just meets a required rejection at ff.

To find the minimum order for a full attenuation mask, use the Filter Order Calculator.

Worked example

This is Pozar's maximally flat low-pass design (Example 8.3, 4th ed.): fc=2f_c = 2 GHz, Z0=50Z_0 = 50 Ω, with at least 15 dB of insertion loss at 3 GHz. That requirement needs N=5N = 5. With Butterworth, low-pass, N=5N = 5, shunt first, the calculator gives:

ElementValue
1 (shunt C)0.98363 pF
2 (series L)6.4380 nH
3 (shunt C)3.1831 pF
4 (series L)6.4380 nH
5 (shunt C)0.98363 pF

At f=3f = 3 GHz the insertion loss is 17.684 dB, which meets the 15 dB requirement. At f=2f = 2 GHz it is exactly 3.0103 dB. These values match Pozar's 0.984 pF, 6.438 nH and 3.183 pF.

Switch to Chebyshev, 0.5 dB at the same order and the loss at 3 GHz rises to 26.651 dB (the elements are 2.7148 pF, 4.8925 nH and 4.0438 pF). Switch to Bessel and it falls to 7.4136 dB. The Bessel filter, however, has a nearly constant group delay: 193.17 ps at DC and 193.17 ps at 1 GHz. The Butterworth delay rises from 257.52 ps at DC to 289.34 ps at 1 GHz. This is the usual trade-off between selectivity and phase linearity.

For band-pass, take Pozar's Example 8.4: 0.5 dB Chebyshev, N=3N = 3, f0=1f_0 = 1 GHz, 10 % bandwidth (100 MHz), series first. The series resonators are L=127.03L = 127.03 nH with C=0.19941C = 0.19941 pF, and the shunt resonator is L=0.72561L = 0.72561 nH ∥ C=34.909C = 34.909 pF. The band edges are 951.25 MHz and 1051.25 MHz, and the loss is 17.826 dB at both 1.1 GHz and 1/1.1 GHz.

Accuracy and validity

The synthesis is exact. The prototype values are closed-form (Butterworth), an exact recursion (Chebyshev) or high-precision tables (Bessel), and the network analysis is exact circuit theory. The golden vectors check:

CheckSourceAgreement
Butterworth g-values, N = 1–10Pozar Table 8.3within 4th-decimal rounding
Chebyshev 0.5 dB and 3 dB, N = 1–10Pozar Table 8.4≤ 1.6 × 10⁻⁴ relative (see below)
Bessel, N = 1–10Zverev; Williams & Taylorwithin 4th-decimal rounding
IL(fcf_c) = 3.0103 dB (Butterworth, Bessel); = ripple (Chebyshev)analytic< 10⁻¹¹
BP/BS log-frequency symmetry, HP mappinganalytic< 10⁻¹²
Group delay (N = 1 closed form, 1/sin⁡(π/2N)1/\sin(\pi/2N) at DC)analytic< 10⁻¹¹

The printed Chebyshev tables differ from the exact recursion in the fourth decimal. Part of that comes from the rounded constant 17.37 for 40/ln⁡10=17.371840/\ln 10 = 17.3718: it alone turns the exact 3 dB value gN+1=5.8089g_{N+1} = 5.8089 into the printed 5.8095. The calculator uses the exact constant.

Practical notes

  • The result is ideal. Real inductors have finite Q and capacitors have ESR. For a band-pass filter, Cohn's estimate of the mid-band dissipation loss is 4.343 ∑gk/(Δ Qu)4.343\,\sum g_k / (\Delta\,Q_u) dB, so a 3 % bandwidth with Qu=100Q_u = 100 already costs several dB. The calculator shows this estimate as a warning.
  • Parasitics. Above a few hundred MHz, keep every part's self-resonant frequency at least 2–3× above the highest frequency of interest, and absorb the pad capacitance into the shunt capacitors. Values below about 0.2 pF or 0.5 nH are comparable to the layout parasitics and trigger a warning.
  • Use standard values. Rounding to E24 or E12 values shifts the response. Re-enter the rounded values in a circuit simulator, or sweep the tolerance, before you commit to a design.
  • Bessel under transformation. Only the low-pass Bessel filter has a maximally flat delay. The high-pass, band-pass and band-stop transformations warp the frequency axis, so the flat delay is lost.
  • Narrow band-pass filters. Below a few percent bandwidth the series resonators need very large L and very small C. A coupled-resonator topology is usually easier to build.

References

  1. D. M. Pozar, Microwave Engineering, 4th ed., Wiley, 2012, §8.3 (low-pass prototypes, Tables 8.3–8.4) and §8.4 (impedance and frequency scaling, band-pass and band-stop transformations).
  2. G. L. Matthaei, L. Young and E. M. T. Jones, Microwave Filters, Impedance-Matching Networks, and Coupling Structures, McGraw-Hill, 1964 (Artech House reprint 1980), §4.05 (Chebyshev, eq. 4.05-2) and §4.07 (maximally flat time delay).
  3. A. I. Zverev, Handbook of Filter Synthesis, Wiley, 1967 (Bessel / maximally flat delay LC tables).
  4. A. B. Williams and F. J. Taylor, Electronic Filter Design Handbook, 4th ed., McGraw-Hill, 2006 (normalized LC tables; Bessel 3 dB normalization).
  5. S. B. Cohn, “Dissipation Loss in Multiple-Coupled-Resonator Filters,” Proc. IRE, vol. 47, no. 8, pp. 1342–1348, 1959.

This calculator's results are checked against 401 independent reference values in automated tests on every change. How we check accuracy.